This article has been reviewed according to Science X's editorial process and policies. Editors have highlighted the following attributes while ensuring the content's credibility:


peer-reviewed publication

trusted source


Electrocatalysis under the atomic force microscope

Electrocatalysis under the atomic force microscope
An overlay of the current signal on a three-dimensional representation of the height image. This clearly shows island-like regions.The newly developed method was used to scan the surface of a bimetallic catalyst material in an aqueous medium. The figure shows an overlay of the current signal on a three-dimensional representation of the height image. This clearly shows island-like regions. Credit: M.Munz/FHI/HZB

A further development in atomic force microscopy now makes it possible to simultaneously image the height profile of nanometer-fine structures as well as the electric current and the frictional force at solid-liquid interfaces. A team from the Helmholtz-Zentrum Berlin (HZB) and the Fritz Haber Institute (FHI) of the Max Planck Society has succeeded in analyzing electrocatalytically active materials and gaining insights that will help optimize catalysts. The method is also potentially suitable for studying processes on battery electrodes, in photocatalysis or on active biomaterials.

To manage the , it will also be important to rapidly develop cheap and efficient materials that can be used to split water or CO2 by electrocatalysis. In this process, part of the electrical energy is stored in the chemical reaction products. The efficiency of such electrocatalysts depends largely on the nature of the electrode-electrolyte interfaces, i.e. the interfaces between the solid electrodes and the typically aqueous electrolyte. However, spatially resolved physical studies of such solid-liquid interfaces are still relatively scarce.

More insights with AFM

Dr. Christopher S. Kley and his team have now developed a new approach to correlative atomic force microscopy (AFM). An extremely sharp tip is scanned across the surface and its height profile is recorded. By attaching the tip to the end of a miniaturized cantilever, the force interactions between the tip and the sample surface, including frictional forces, can be measured with high sensitivity.

In addition, the electrical current flowing through the mechanical contact can be measured, provided a voltage is applied. "This allowed us to simultaneously determine the , the mechanical-chemical friction and the morphological properties in situ (i.e. under the relevant liquid-phase conditions rather than in vacuum or in air)," says Kley.

Copper-gold electrocatalyst

Using this method, the scientists now studied a nanostructured and bimetallic copper-gold electrocatalyst, in collaboration with Prof. Beatriz Roldán Cuenya from the Fritz-Haber-Institute (FHI). Among others, such materials are used in the electrocatalytic conversion of CO2 into energy carriers.

Electrocatalysis under the atomic force microscope
The principle of correlative atomic force microscopy in contact mode: a fine tip at the end of a cantilever scans the surface. This allows force interactions between the tip and the sample surface to be measured, including frictional forces. If a voltage is also applied, the electric current flowing through the contact can also be measured. Credit: M.Munz/FHI/HZB

"We were able to clearly identify islands of copper oxide with higher electrical resistance, but also grain boundaries and low-conductivity regions in the hydration layer where the catalyst surface comes into contact with the aqueous electrolyte," says Dr. Martin Munz, first author of the study.

Such results on catalyst-electrolyte interfaces help to optimize them in a targeted manner. "We can now observe how local electrochemical environments influence charge transfer at the ," says Kley.

"However, our results are also of general interest to , especially for the study of electrochemical conversion processes, which also play a role in battery systems."

Insights into solid-liquid interfaces can also be useful in completely different areas of research, such as understanding corrosion processes, nanosensor systems, and possibly addressing scientific queries in fluidics and environmental sciences, such as dissolution or deposition processes on exposed to water.

The findings are published in the Journal of the American Chemical Society.

More information: Martin Munz et al, Nanoscale Electron Transfer Variations at Electrocatalyst–Electrolyte Interfaces Resolved by in Situ Conductive Atomic Force Microscopy, Journal of the American Chemical Society (2023). DOI: 10.1021/jacs.2c12617

Citation: Electrocatalysis under the atomic force microscope (2023, March 9) retrieved 28 September 2023 from
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

Explore further

Deconvoluting the data: Charge density distributions of electric double layers


Feedback to editors