Tuning the surface gives variations to metal foils

Tuning the surface gives variations to metal foils
Formation mechanism of large area single crystalline Cu foils with different surface structures via the annealing of peroxide Cu foils. Credit: IBS

Just as cloning in biology allows for the creation of one or more replicas of the exact same genes, seeded growth in chemistry can produce a very large metal foil with the exact same surface texture as that of a seeded one. Seeded growth is very popular in synthesizing three-dimensional (3-D) single crystals: 3-D crystals are always grown into the same shapes, just as salts are invariably cubic single crystals.

Meanwhile, very thin foils/films can grow into different types depending on structures. As such, applications can vary. Great efforts had been dedicated to the synthesis of single crystalline metal foils as they have many important applications, such as (i) a substrate to support the synthesis of various two-dimensional (2-D) materials, (ii) engineering the properties of the material deposited on it, (iii) allowing for selective catalysis, and (iv) fabricating metal wires with optimized electrical and thermal conductivities. Despite such possibilities, seeded growth has rarely been applied to grow thin films due to a lack of knowledge on how to control the growth process.

Prof. Feng Ding's group from the Center for Multidimensional Carbon Materials, within the Institute for Basic Science (IBS, South Korea), in collaboration with Prof. Kaihui Liu's group and Prof. Enge Wang's group from Peking University, as well as Prof. Dapeng Yu's group from Southern University of Science and Technology, reported how to give variations to single crystalline metal foils. Via the oxidation-led annealing plus seeded growth strategy, the research team obtained more than 30 types of copper foils the size of A4 paper (~30×21 cm2), which is roughly the same size as US legal.

Tuning the surface gives variations to metal foils
Large area single crystalline Cu foils with high-index surfaces. Credit: IBS

The research team has been exploring copper foils, one of the most popular substrates to support the growth of graphene and other 2-D materials. Though they obtained single crystal copper (Cu) foils in their previous study (Science Bulletin, 2017, 62, 1074-1080), they were mostly Cu (111), whose surface is ultra-flat and thus less active than those with step edges and kinks. Through theoretical calculations, the research team concluded that Cu (111) tends to be formed more easily than other types, as the Cu (111) surface has the lowest surface energy and thus is the most favorable structure in nature. This reasoning led them to tune the surface energy of Cu foils in order to obtain single-crystal metal foils with desired surface types.

The research team cut out the "gene" of a small single crystalline foil and "pasted" the seed (gene) to create very large Cu foils with the exact same as that of the inherited one. To obtain single crystalline metal seeds with various surface structures, polycrystalline Cu foils were first oxidized and then annealed at a high temperature (1020 °C), which is close to the melting point of Cu, for several hours. When the Cu was oxidized, both its upper and lower surface were covered by a layer of copper oxide (CuxO). As the pure Cu surface disappears due to the oxidation, the two surfaces of a Cu foil were transformed into two Cu-CuxO interfaces after pre-oxidation. This alteration switched the driving force of annealing from surface energy to interface energy. "We have proved that, unlike that of the surface energies, the differences of the interface energies of different Cu foils are negligible, so the polycrystalline Cu foils can be annealed into many different types of randomly." explains Professor Feng Ding, the corresponding author of the study.

A small piece of foil was then cut from a large single-crystal foil with a desired surface structure as a seed for mass production. The research team found that the annealing of a large polycrystalline Cu foil with such a seed will lead to a large single crystal Cu foil with the exact same surface structure (Figure 2, stage 2).

Tuning the surface gives variations to metal foils
Illustration of the process of obtaining single crystalline Cu foils with different surface structures. Credit: IBS

Great theoretical and experimental efforts were devoted to understanding how these single crystalline Cu foils were formed during the annealing. Such a process can be understood in two stages. First, the surface structure of the seed was copied to the lower part of the large polycrystalline Cu foil and formed an abnormal grain (a grain which is much larger than others and has the advantage to grow up further) with a specific surface structure. Second, the growth of the abnormal grain finally results in a very large single-crystal Cu foil with the designated surface structure.

From hundreds of annealing experiments, the research team obtained a library of single crystalline Cu foils with more than 30 types of different , as shown in Figure 3. The dimensions of the obtained single crystalline Cu foils reached 39 * 21 cm2, which was limited by the size of the annealing furnace.

Besides the Cu foils, the researchers proved that this seeded growth strategy can be applied to fabricate large-area single-crystal foils of other metals, suggesting that various types of single-crystal foils of most metals could be available in the near future. "This achievement demonstrates a practical method for scalable synthesis of extremely large transition metal single crystal foils with different surface types, which was long desired for both fundamental science and engineering applications. Our achievement opens many possibilities, such as to use single crystal metals as conducting channels in micro-devices; use these single crystal metal foils as templates for controllable synthesis of various two-dimensional materials; grow large area molecular patterns with selected metal foils; and selectively catalyze chemical reactions on a surface with a specific structure," notes Professor Kaihui Liu.

The research team will next aim to understand the mechanism of this oxidation-led seeding and seeded growth at the atomic level. Experimental efforts to synthesize various types of single crystal metal foils of different metals or alloys will continue, as well as exploring broad applications of these foils.

The study is published in Nature.

Explore further

Producing defectless metal crystals of unprecedented size

More information: Muhong Wu et al. Seeded growth of large single-crystal copper foils with high-index facets, Nature (2020). DOI: 10.1038/s41586-020-2298-5 , www.nature.com/articles/s41586-020-2298-5
Journal information: Advanced Materials

Citation: Tuning the surface gives variations to metal foils (2020, May 27) retrieved 3 July 2020 from https://phys.org/news/2020-05-tuning-surface-variations-metal-foils.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

Feedback to editors

User comments