Three innovative components can pave the way for cheaper wind energy generation

May 28, 2015,

Wind turbines began cropping up across the landscapes of Spain and Germany in the 1990s. These two countries have the highest wind energy production in the EU. But according to the Global Wind Energy Council, the global installed power capacity in Europe—which is 134,007 MW—has been surpassed by Asia with 141,964 MW, at the end of 2014. The wind power industry is arguably the most mature—and fastest developing—among renewable energies. But, there is still considerable room for improvement to compete with other sources of electricity.

Even though and management play a crucial role in wind energy uptake across Europe, reducing cost by relying on research and development (R&D) is of the challenges researchers are exploring. This is the aim of the European research consortium WINDTRUST.

The project plans to reduce costs by improving the reliability of key components of the turbine. "We are focusing on further enhancing the design of three key components with high improvement potential: the rotor blades, the power electronics and the wind turbine controller," says Mauro Villanueva, director of technology development at Gamesa, the wind turbine company that leads the consortium, who is also project coordinator.

One avenue of research has been to improve the durability of turbine rotorblades. "We have already begun to optimise the use of carbon fibre to increase rotorblade durability and reduce component weight. This will contribute to extending the overall life of the turbine to 20 to 30 years," says Fernando García Ayerra, a project manager at Gamesa and technical director of the project.

Developments are also underway to enhance turbine control. "At the same time, we are developing control algorithms that should reduce extreme and fatigue loads of the turbine in order to maximise the balance between energy production and machine life," says García Ayerra.

But increasing the reliability of power electronics is also key. Villanueva explains that it can be done by "implementing improved electronic topology, redundant circuitry components [and] control algorithms that maximise performance versus component life, as well as [by] deploying sensors to monitor the performance and remaining life, so that predictive maintenance [of the turbine] can take place."

But reducing energy costs is not necessarily about making each component cheaper. "Although the cost of the enhanced parts will probably be higher, reduced cost of repairs and less downtime will render an increase in the amount of energy produced," Villanueva notes. "This increase is expected to exceed such costs, thereby leading to an overall reduction of the cost of energy," he adds.

There are plans to test all these new technologies together. Such innovative components are likely to be fitted onto an onshore 2 MW prototype located at the experimental Alaiz Windfarm in Pamplona, Spain. "This will enable us to compare the performance with those of existing, well-known turbines. And although this project is aimed at onshore, most of the results are also applicable to offshore, where much greater benefits should be obtained," explains Villanueva.

This could also matter for the consumer. "It is important that people understand that all the money invested in R&D is focused towards the reduction of the cost of wind energy, which will hopefully reach the final consumer," Villanueva notes.

What does the future hold for wind energy generation in terms of adaptation across Europe? Villanueva says, "The creation of a truly European energy market and system, that is, pricing, transport and management, will allow the maximum deployment of sustainable energy generation sources".

Because of the size of the EU and its variable meteorological characteristics, produced in excess in one area will be transmitted to and consumed in another, where wind is lower. And the same would happen with photovoltaic. García Ayerra concludes: "This will minimise curtailments—wind farms stopped during periods of consistent wind blow—and reduce the need for costly local energy storage systems."

Explore further: European project sets out to boost the wind energy sector by further improving the reliability of wind turbines

Related Stories

Vortex Bladeless aims for lower-cost wind energy approach

May 18, 2015

A technology leap forward in wind energy? Or, as the company in charge calls it, a "new paradigm" of wind power, lowering costs, requiring no training, using fewer supplies? They believe they have a great idea and they aim ...

Denmark champions wind power, sets record

January 10, 2015

Denmark has had a record year for wind power production. Denmark got 39.1 percent of its overall electricity from wind in 2014. That figure is according to the country's Climate and Energy Ministry.

Recommended for you


Adjust slider to filter visible comments by rank

Display comments: newest first

not rated yet May 28, 2015
This will contribute to extending the overall life of the turbine to 20 to 30 years,

Weren't they already supposed to last for 25 years?

That's what we've been sold all this time. For example:

The Financial Times also quotes Dale Vince, the founder of Ecotricity, one of the UK's oldest renewable energy companies, saying the study was "just more anti-wind propaganda".

"Today's turbines have been designed and built to last 25 years,"

How can the wind industry claim that they're improving the durability of the technology to the point that they're already claiming it is at, unless they've been lying all this time?
1 / 5 (1) May 28, 2015
Gosh, Eikka,we don't know. Will the power be "Too cheap to meter"?

Who lied to us?

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.