Physicists find weak spots in ceramic/graphene composites

Physicists found weak spots in ceramic/graphene composites
Crack propagation over grain boundaries in the composite. Graphene plates are marked by green lines. Credit: Peter the Great St.Petersburg Polytechnic University

Physicists and materials scientists from Peter the Great St.Petersburg Polytechnic University (SPbPU) analyzed the structures in nanomaterials made of ceramic and graphene plates, in which cracks appear most frequently. The results of the first trial of the model, that describes this regularity, were published in the Mechanics of Materials Journal. This model will help in creation of crack-resistant materials. The research was supported by the Russian Science Foundation grant.

Graphene is the lightest and strongest carbon composite. Moreover, it has a very . Because of these characteristics graphene is often included in the composition of new ceramic-based materials. Ceramics are resistant to high temperatures, and, if carbon modifications are added, the composites become multifunctional. In the future they can be used in production of flexible electronic devices, sensors, in construction and aviation.

It is known from many experimental studies of such composites that their mechanical characteristics are set by the graphene proportion in the composition and by the size of graphene plates allocated in the ceramic matrix. For example, in the case of low graphene concentration, high crack resistance was achieved with the help of long plates. However, in one of the recent experiments of synthesis of materials from alumina ceramics and graphene, the opposite effect was shown: as the plates were bigger, the crack resistance was weaker. The researchers from Saint Petersburg have developed a theoretical model that explains this paradox.

The physicists supposed that the formation of cracks in the composites is connected with the boundaries of so-called ceramic —microscopic crystals that form the material. Graphene plates in the composites can be located both at the boundaries of ceramic grains and inside grains. In the course of the tensile deformation of nanocrystalline materials, the grains slide relative to each other, and the cracks spread over their boundaries. But why do graphene additions stop this process in some cases and not stop it in others? To find the answer, the scientists developed a that takes into account the tensile load, the force of friction, elastic moduli of the composite, and the correlation between the dimensions of ceramic grains and graphene plates. With the help of the model, the scientists computed the critical values of the stress intensity factor for three different composites. When these values were exceeded, cracks spread all over in the material. The composites varied in the size of ceramic grains (from 1.23 to 1.58 micrometers) and the length and width of graphene plates (from 193 to 1070 and from 109 to 545 nanometers).

It was found that the closer the length of graphene plates to the length of grain boundary lines, the lower the critical value of the stress intensity factor. The value difference for different materials comes up to 20%. It is congruent to experimental data published earlier: just at close values of grain boundary length and the length of graphene plates, the crack resistance of the material dropped. This implies that to make the material stronger, graphene plates must be substantially smaller in length than ceramic grains.

"The observed regularity is valid for fine-grained ceramics, and, after all, by reducing the grain size, the creators of new composite materials add more functionality to them," explains Alexander Sheinerman, Doctor of Physical and Mathematical Sciences, the head of the research laboratory "The Mechanics of New Nanomaterials" of the Advanced Manufacturing Technologies Center of the National Technology Initiative NTI SPbPU. "Therewith, the effects of grain refinement can be contradictory, for example, the hardness rises, but the material becomes more fragile. Our model helps to pick the correlation of the size and the size of grains, which provide better mechanic and functional characteristics."


Explore further

Graphene is 3-D as well as 2-D

More information: A.G. Sheinerman et al, Effect of grain boundary sliding on fracture toughness of ceramic/graphene composites, Mechanics of Materials (2019). DOI: 10.1016/j.mechmat.2019.103126
Provided by Peter the Great Saint-Petersburg Polytechnic University
Citation: Physicists find weak spots in ceramic/graphene composites (2019, September 27) retrieved 20 October 2019 from https://phys.org/news/2019-09-physicists-weak-ceramicgraphene-composites.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.
13 shares

Feedback to editors

User comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more