Direct current, another option to improve the electrical power transmission

April 30, 2014
In the future HVDC grids are expected to coexist with alternating current grids. Credit: UPV/EHU

Even though today most of the electricity transmission lines are alternating current ones, in some cases direct current lines are also used.And researchers are becoming aware that in some cases direct current lines are more suitable than alternating current ones.In this area, the GISEL research group of the Department of Electrical Engineering of the UPV/EHU-University of the Basque Country has been working to improve the technology needed for this conversion.The aim has been that this transmission should be done in a more straightforward, smoother and consequently less expensive way.

Electricity is normally transmitted by means of alternating current, but it is not the only way and not always the best one.In some cases, (HVDC) is used. In Spain, for example, there is only one direct current line, the one that connects mainland Spain with the Balearic Islands; all the remaining ones transmit electricity by means of alternating current.

In fact, "direct current continues to be highly suitable for underwater and underground lines," asserted Marene Larruskain, one of the engineers in the UPV/EHU's GISEL group. Furthermore "less investment is needed to build direct current lines, and there are fewer losses in electricity transmission. "However, as most of the lines in the power grid are alternating current ones, converters are needed to change the type of electricity transmission, and they are very costly."That is why direct current lines are appropriate beyond a certain length," specified Larruskain. And this is in fact the use that is made of high voltage direct current lines, to transmit electricity over very long distances; indeed, the longest lines that exist are direct current ones. "There are facilities worldwide thattransmit direct current electricity.The typical examples are the transmission lines of large hydraulic power stations: the Itaipu power station in South America, the Three Gorges power station in China, etc.

Bearing in mind that right now most of the transmission of electricity is done by means of alternating current lines, "our aim is in no way to replace these lines by direct current ones. Our proposal is based on using direct current as a solution in cases where there are problems with the alternating current lines," explained Larruskain. Renewable energies could could an example of this.Renewable energies are produced in a very irregular way; the wind, for example, could blow very strongly at some moments and very lightly in others.And the output may not coincide with moments of peak energy consumption."One way of solving the problem caused by this situation for the electricity supply could be to connect the farms or parks of various countries where renewables are produced. That way, if at one moment one region has a high consumption of energy but is not producing renewable energy, its demand could be metby using renewable energy which is being produced somewhere else," explained the researcher. As there is a global grid, the variability in production of renewables could be balanced. The UPV/EHU's GISEL group is proposing that these global grids should be direct current ones.

The aim, to assist transmission

The GISEL group is working to improve the energy exchange converters between direct current lines and alternating current ones.Specifically, they are working on new technology for converters known as VSCs (Voltage Source Converters).Compared with conventional technology, "the VSC has many advantages; among others, it is easier to control the power that is transmitted, and that is very important on wind farms, for example. At the same time, given the fact that direct current has great economic advantages in underwater lines, it is very appropriate for them."

However, VSC technology has a number of drawbacks: firstly, its capacity to transmit energy is lower, the energy losses are greater and it does not respond well when problems arise. For example, if there is a short circuit, the system has problems. That is why "we're working to minimize those problems," explained the researcher.

Secondly, the researchers want to make use of the advantages of both means of transmitting electricity to be able to address growing power consumption. And it is a fact that "even though more and more energy is being produced to meet the demand, problems may arise when it comes to transmitting that energy. It is not always possible to incorporate the surplus energy produced into the already existing lines owing to their limits. In these cases, the use of direct current could solve the problem of the alternating current lines already installed, because, among other things, the HVDC lines can transmit more electrical power," explained Larruskain.

The GISEL research group has studied how to make the features of the alternating current and direct current lines compatible. The electricity lines of alternating current are three-phase. For example, the number of conductors are three, or multiples of that number. On the other hand, HVDC lines have two poles: a positive one and a negative one. "How are we going to divide two poles into three conductors?" wondered Larruskain. If we use one pole for each phase, one of the conductors of the original line will remain free and part of the power will be lost. That is why a line and a half of alternating current corresponds to each pole of direct current. Even though it looks impossible, there are various ways of making this distribution.

"In the future HVDC grids are expected to coexist with alternating current grids, which are in the majority nowadays.Transmitting direct current via the currently existing lines could be a first step towards building HVDC grids," explained the UPV/EHU engineer.

Explore further: A world record in direct current transmission

More information: M. Larruskain, I. Zamora, O. Abarrategui, A. Iturregi. January 2014. "VSC-HVDC configurations for converting AC distribution lines into DC lines". International Journal of Electrical Power & Energy Systems 54: 589 -597 040 0142-0615

M. Larruskain, I. Zamora, O. Abarrategui, A. Iturregi. 2013. "A Solid-State Fault Current Limiting Device for VSC-HVDC Systems". International Journal of Emerging Electric Power Systems, Volume 14, Issue 5: 375-384, ISSN (online version) 1553-779X, ISSN (print) 2194-5756, DOI: 10.1515/ijeeps-2013-0017.

Related Stories

A world record in direct current transmission

May 3, 2011

Siemens is building power converter stations for a high-voltage direct current (HVDC) transmission system with a record capacity of 2 x 1,000 megawatts. Beginning in 2013 the new HVDC PLUS technology will transmit 2,000 megawatts ...

High voltage at the world's tallest dam

April 28, 2014

Siemens is bringing electricity to the surface from the world's deepest arch-dam turbines. The dam of the Jinping-1 Hydropower Station in China's Sichuan province is 305 meters tall; the turbines are located 230 meters deep. ...

Enhanced power transmission for HVDC

November 22, 2013

Siemens is researching new technology to enhance the efficiency of high-voltage direct-current transmission (HVDCT). This minimizes losses during power transmission and is one of the key technologies required to make better ...

Saving energy with power grid of the future

November 2, 2010

Green energy too comes out of the electricity socket, but to get there it has to travel a long journey – from wind turbines in the North Sea or regional solar, wind and biogas power plants. On the way to the consumer ...

Recommended for you

'Droneboarding' takes off in Latvia

January 22, 2017

Skirted on all sides by snow-clad pine forests, Latvia's remote Lake Ninieris would be the perfect picture of winter tranquility—were it not for the huge drone buzzing like a swarm of angry bees as it zooms above the solid ...

Singapore 2G switchoff highlights digital divide

January 22, 2017

When Singapore pulls the plug on its 2G mobile phone network this year, thousands of people could be stuck without a signal—digital have-nots left behind by the relentless march of technology.

Making AI systems that see the world as humans do

January 19, 2017

A Northwestern University team developed a new computational model that performs at human levels on a standard intelligence test. This work is an important step toward making artificial intelligence systems that see and understand ...

Firms push hydrogen as top green energy source

January 18, 2017

Over a dozen leading European and Asian firms have teamed up to promote the use of hydrogen as a clean fuel and cut the production of harmful gasses that lead to global warming.


Adjust slider to filter visible comments by rank

Display comments: newest first

not rated yet Apr 30, 2014
If you want to increase the amount of power transmittable over a line, can't you just increase the frequency?
5 / 5 (1) Apr 30, 2014
If you want to increase the amount of power transmittable over a line, can't you just increase the frequency?

No. Increasing the frequency simply increases capacitive leakage.

Increasing frequency increases the throughput of transformers, but not the lines themselves.
5 / 5 (1) Apr 30, 2014
If frequency of AC transmission is changed, there needs to be converters for frequency changing at both ends of line. Then the technology would be more complicated than using DC lines, because AC->DC and then DC->AC converters are simpler than would be frequency converters for AC->AC when source and target are not having the same frequency. Normal AC->AC voltage conversion keeping the same frequency is done by transformer, which is simple compared to DC->AC converters. In fact frequency changing AC->AC is typically internally AC->DC + DC->AC.

Another factor is the fact that DC transmission lines can use higher voltage than any AC, since line isolation for AC lines have to withstand peak AC voltage which is 1.4 times the RMS voltage.

One factor that also favors the DC for long distances is the fact that in AC transmission the source and drain are phase locked to grid frequency and this needs delicate adjustments between those grids or the power transfer does not work.
not rated yet Apr 30, 2014
One factor that also favors the DC for long distances is the fact that in AC transmission the source and drain are phase locked to grid frequency and this needs delicate adjustments between those grids or the power transfer does not work.

Not really. There are slight frequency and phase differences all over the AC network, where power flows from higher frequency to lower frequency by advancing the speed of the generators at that part of the network until a balance is reached. Once in sync, they tend to naturally stay in sync unless something drastic happens. This is analogous to DC current flowing from higher voltage to lower voltage.

What you're referring to is the fact that two power lines carrying AC current may become antiphase in regards to one another with one line significantly longer than the other, and connecting them together would short both as they try to synchronize, so you have to be careful about making loops and shortcuts through your network.

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.