Savvy injection molding

Apr 02, 2010
IFAM researchers inspecting components produced using metal injection molding. (© Fraunhofer IFAM)

( -- With the help of neural networks, in which complex algorithms are used to monitor critical process steps, engineers are paving the way for zero-defect production in the area of metal powder injection molding. The gain for manufacturers is less waste combined with time savings.

The used in the hinges of spectacle frames, surgical instruments or artificial heart valves are often very small. For some years now, manufacturers of components with complex geometries of this type have relied on a special production process: metal injection molding. Things can occasionally go awry during production, and then it is often impossible to detect defects until after sintering, the final step in the process chain, by which time it is too late to correct the defect.

Now, researchers at the Fraunhofer Institute for Manufacturing and IFAM are working towards achieving zero-defect production. Their idea is that, at any time during the molding process, the system should be able to monitor all parameters - such as weight, pressure and temperature - and to deliver a verdict on the quality of the component.

"In this way, errors, dimensional inaccuracies and defects such as cracks, warps or cavities can be detected on line,« explains IFAM project manager Dr. Thomas Hartwig. "This will allow the manufacturer to respond immediately by changing the relevant settings."

In the long run the system can, if required, even be programmed to alter the parameters fully automatically. The necessary technical support is provided by a neural network developed for metal injection molding (MIM) in a joint effort by the IFAM engineers and algorithmica technologies, a private company. "The neural network is based on highly complex algorithms," says Hartwig. "Its advantage over existing solutions is that it is self-learning."

After a mandatory initial training phase it can interpret all the measured data in the system, detecting correlations between them that would be impossible to find without the network. All information of relevance to the manufacturer can be given by the process control system, for instance the final weight of the component if the pressure or temperature is changed at a given step in the process.

"Our goal with neural networks is to reduce reject rates by at least 50 percent," says Hartwig. "This represents a huge cost saving for manufacturers because the raw materials are so expensive. Until now, companies often had to reject large numbers of components in the first few days before quality requirements could be met again." Another advantage of neural networks is that they could eventually make quality checks superfluous and could also be deployed in other types of series production such as die-casting in the light-metal industry. Having successfully produced a test component with the aid of neural networks, the researchers are now looking for industrial partners.

Explore further: Drone postal deliveries begin in Switzerland

Related Stories

First powder injection molding process for pure niobium

Oct 17, 2005

Penn State researchers have developed the first powder injection molding process for pure niobium, a biocompatible material similar to platinum and titanium but cheaper. The researchers, who are based in the University's Cen ...

Electrical components in a single molding operation

Sep 06, 2004

Siemens researchers have developed a composite made of plastic and metal that can be processed like a plastic, but has the electrical and electromagnetic properties of metal. The new plastic-metal hybrid is ...

Intelligence inside metal components

Nov 24, 2009

Up to now, extreme production temperatures made it impossible to equip metallic components with RFID chips during the operating process. At Euromold in Frankfurt (Dec. 2-5), Germany, Fraunhofer researchers ...

Bone-hard biomaterial

Mar 22, 2010

Screws used in surgical operations are often made of titanium. They usually have to be removed after a while or replaced by new ones. A new biomaterial makes this unnecessary. It promotes bone growth and is ...

Printing of components with functional ink

Apr 08, 2005

Time is money - even in component manufacturing. Researchers can continuously print out three-dimensional metal parts using a rapid manufacturing process. The unique feature is that they can vary the material ...

Recommended for you

Drone postal deliveries begin in Switzerland

12 hours ago

Wondering where your package is? Look up! Switzerland's postal service said Tuesday it had begun testing parcel deliveries by unmanned drones, although widespread use of the flying postmen is not likely to kick in for another ...

Omnidirectional free space wireless charging developed

12 hours ago

Mobile devices, such as smartphones and laptops, have become indispensable portable items in modern life, but one big challenge remains to fully enjoying these devices: keeping their batteries charged.

Europe's deepest glider to be developed

Jul 06, 2015

19 partners from across Europe have come together to develop Europe's first ultra-deep-sea robot glider. This glider will be capable of sampling the ocean autonomously at depths of 5000m, and maybe more in ...

Researchers help reconstructing the Michelangelo bronzes

Jul 06, 2015

Engineers and imagers from the University of Warwick's Warwick Manufacturing Group (WMG) and anatomists from Warwick Medical School at the University of Warwick are helping Art historians from the University ...

User comments : 0

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.