Better biomedical devices, wearable displays may result from tiny light-guiding structures

Better biomedical devices, wearable displays may result from tiny light-guiding structures
An envisioned example of 3D optical waveguides integrated in one flexible PDMS substrate with microfluidic channels. Blue wires illustrate an imaging waveguide bundle. Red wires exemplify optical communication channels. Green wires depict optical systems of flow cytometry or spectroscopy. Credit: Optical Materials Express (2018). DOI: 10.1364/OME.9.000128

For the first time, researchers have fabricated light-guiding structures known as waveguides just over one micron wide in a clear silicone commonly used for biomedical applications. The tiny, flexible waveguides can be used to make light-based devices such as biomedical sensors and endoscopes that are smaller and more complex than currently possible.

"To the best of our knowledge, these are the smallest optical waveguides ever created in polydimethylsiloxane, or PDMS," said research team member Ye Pu of École Fédérale de Lausanne in Switzerland. "Our flexible waveguides could be integrated into microfluidic lab-on-a-chip systems to eliminate bulky external optics needed to perform blood tests, for example. They might also deliver light for wearable devices such as a shirt featuring a display."

As reported in the journal Optical Materials Express, the new optical waveguides are not only thinner than a piece of dust, they also exhibit very low light loss when used with certain wavelengths of light. A light-based signal can travel through the new waveguides for 10 centimeters or more before an unacceptable degradation of the signal will occur.

Creating structures with light

The researchers made the new waveguides by optimizing laser direct writing, a microfabrication approach that creates detailed 3-D structures by polymerizing a light sensitive chemical with a precisely positioned focused laser. Polymerization converts relatively called monomers into large, chainlike polymers.

The new approach does not require a photoinitiator, which is typically used to efficiently absorb the and convert it into chemical energy that initiates polymerization. "By not using a photoinitiator, we simplified the and also enhanced the compatibility of the final device with living tissue," Pu said. "This enhanced biocompatibility could allow the approach to be used to make implantable sensors and devices."

The new flexible waveguides could also serve as for photonic printed that use high-speed optical signals rather than electrical links to transmit data in computers and other electronic devices.

Confining the light

To achieve a small optical that efficiently confines light, there must be a large difference between the refractive index of the material making up the waveguides and the surrounding PDMS. The researchers used phenylacetylene for the waveguides because, compared to traditionally used materials, it has a higher refractive index once polymerized. As an added benefit, it also can be easily loaded into PDMS simply by soaking the PDMS in liquid phenylacetylene.

After soaking the PDMS in phenylacetylene, the researchers used focused ultrafast laser pulses to induce an optical phenomenon known as multiphoton absorption in which multiple photons are absorbed at once. Multiphoton laser direct writing produces much finer structures than one-photon processes because the volume of polymerization at each writing spot is much smaller. Using multiphoton laser direct writing also allowed the researchers to directly initiate phenylacetylene polymerization without a photoinitiator. They then evaporated any unpolymerized phenylacetylene by heating the PDMS.

The researchers showed that this new approach could make flexible waveguides in PDMS that are just 1.3 microns wide. For the 650 to 700 nanometer spectral band, only 0.07 percent of the transmitted through the waveguides is lost every centimeter. Optimizing the setup would likely allow fabrication of waveguides that are smaller than 1 micron, according to the researchers.

A flexible endoscope

The are now working to improve the yield of the fabrication process by developing a control system that would help avoid material damage during writing. They also plan to create an array of narrow waveguides in PDMS that could be used to construct a very flexible endoscope with a diameter of less than one millimeter.

"Such a small, mechanically flexible endoscope would allow a number of hard-to-reach places in the body to be imaged for diagnosis in the clinic, or for monitoring in a minimally invasive surgery," said Pu.


Explore further

New low-cost method to produce light-based lab-on-a-chip devices for fast medical tests

More information: Giulia Panusa et al, Photoinitiator-free multi-photon fabrication of compact optical waveguides in polydimethylsiloxane, Optical Materials Express (2018). DOI: 10.1364/OME.9.000128
Journal information: Optical Materials Express

Citation: Better biomedical devices, wearable displays may result from tiny light-guiding structures (2018, December 11) retrieved 21 October 2019 from https://phys.org/news/2018-12-biomedical-devices-wearable-result-tiny.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.
31 shares

Feedback to editors

User comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more