New sound diffuser is ten times thinner than existing designs

June 6, 2017 by Matt Shipman
A conventional, two-dimensional conventional Schroeder diffuser (on the left), compared to a new, 'ultra-thin' two-dimensional Schroeder diffuser (at right). The ultra-thin diffuser is 10 times thinner. Credit: Yun Jing

Researchers from North Carolina State University and Nanjing University have developed an "ultra-thin" sound diffuser that is 10 times thinner than the widely used diffusers found in recording studios, concert venues and movie theaters to reduce echoes and improve the quality of sound. The new design uses less material, which would reduce cost, as well as taking up far less space.

In a typical room with flat walls, usually bounce off the walls, like light reflecting off a mirror. This creates echoes and overlapping waves that result in uneven sound quality depending on where you are in the room.

"Sound diffusers are panels placed on the walls and ceiling of a room to scatter sound waves in many different directions, eliminating echoes and undesirable sound reflections - ultimately improving the quality of the sound," says Yun Jing, an assistant professor of mechanical and aerospace engineering at NC State and corresponding author of a paper on the work.

But the most widely used diffusers, called Schroeder diffusers, can be very bulky. That's because the size of a diffuser is governed by the wavelength of the sound it needs to diffuse. Specifically, the depth of a Schroeder diffuser is about half of the wavelength of the lowest sound it needs to diffuse.

For example, a typical man's voice can be as low as 85 hertz, with a wavelength of 4 meters or 13.1 feet. If that's the lowest sound the Schroeder diffuser will have to deal with, the diffuser would need to be roughly 2 meters - or just over 6.5 feet - thick.

But the new, ultra-thin diffuser design requires a thickness that is only 5 percent of the sound's wavelength. So, instead of being 2 meters thick, it would only be 20 centimeters - or less than 8 inches - thick.

"Diffusers are often made out of wood, so our design would use 10 times less wood than the Schroeder diffuser design," Jing says. "That would result in lighter, less expensive diffusers that allow people to make better use of their space."

This reduction in diffuser thickness is made possible by the design of the individual cells in the diffuser.

A Schroeder diffuser looks like a panel of evenly spaced squares, which are identical in length and width, but vary in depth.

The ultra-thin diffuser also consists of evenly spaced squares, but the squares appear to be of different sizes. That's because each of the squares is actually an aperture that opens into a thin, underlying chamber. These chambers all have identical dimensions, but the size of the apertures varies significantly - accomplishing the same sound diffusion as the much larger Schroeder diffusers.

"We've built fully functional prototypes using a 3-D printer, and it works," Jing says. "The should work just as well using wood."

The paper, "Ultra-thin Acoustic Metasurface-Based Schroeder Diffuser," is published in the American Physical Society journal Physical Review X.

Explore further: New use for an old 'trouble maker'

More information: Yifan Zhu et al, Ultrathin Acoustic Metasurface-Based Schroeder Diffuser, Physical Review X (2017). DOI: 10.1103/PhysRevX.7.021034

Related Stories

New use for an old 'trouble maker'

March 21, 2014

(Phys.org) —A 'trouble maker' from a bygone method of glass production could find a new use as an optical diffuser in medical laser treatments, communications systems and household lighting.

Recommended for you

Enhancing the quantum sensing capabilities of diamond

November 22, 2017

Researchers have discovered that dense ensembles of quantum spins can be created in diamond with high resolution using an electron microscopes, paving the way for enhanced sensors and resources for quantum technologies.

Study shows how to get sprayed metal coatings to stick

November 21, 2017

When bonding two pieces of metal, either the metals must melt a bit where they meet or some molten metal must be introduced between the pieces. A solid bond then forms when the metal solidifies again. But researchers at MIT ...

Imaging technique unlocks the secrets of 17th century artists

November 21, 2017

The secrets of 17th century artists can now be revealed, thanks to 21st century signal processing. Using modern high-speed scanners and the advanced signal processing techniques, researchers at the Georgia Institute of Technology ...

0 comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.