Inspired by steel, nanomanufacturing gets wear-resistant carbide tip

February 9, 2012
In this photo, carbon and silicon sharpened to a nano-sized tip integrated on the end of a silicon microcantilever for use in atomic force microscopy. The tip is heated to approximately 800 degrees Celsius, making it glow in this photo.

( -- Scientists at the University of Pennsylvania, the University of Wisconsin-Madison and IBM Research - Zurich have fabricated an ultrasharp silicon carbide tip possessing such high strength that it is thousands of times more wear-resistant at the nanoscale than previous designs. The new tip, which is 100,000 times smaller than the tip of a pencil, represents an important step towards nanomanufacturing for applications, including bio sensors for healthcare and the environment.

The search for hard materials to extend the working life of sharp tools is an age-old problem that started with the first chisels used in stone carving. Eventually iron was discovered and steel tools revolutionized the era. Today, the challenge remains the same, but on a much smaller scale--the need for a nano-sized tip that is both ultrasharp, yet still physically robust, particularly under and harsh chemical environments.

"The dream tip material for thermomechanical should have a high hardness, temperature stability, chemical inertness, and high ," said Dr. Mark Lantz, manager in storage research at IBM Research - Zurich. "With this novel tip we continue to deliver on IBM's vision of a smarter, instrumented world with microscopic sensors monitoring everything from to patient care."

Extending their previous successful collaboration, scientists at the University of Pennsylvania, the University of Wisconsin-Madison and IBM Research - Zurich have developed a new, resistant nano-sized tip that wears away at the rate of less than one atom per millimeter of sliding on a substrate of dioxide. This is much lower than the wear rate of conventional silicon tips and its hardness is 100 times greater than that of the previously state-of-the-art silicon oxide-doped diamond-like carbon tips developed by the same collaboration last year.

"Compared to our previous work in silicon, the new carbide tip can slide on a silicon dioxide surface about 10,000 times farther before the same wear volume is reached and 300 times farther than our previous diamond-like carbon tip. This is a significant achievement that will make both practical and affordable," said Prof. Robert W. Carpick, University of Pennsylvania.

To create the new tip, scientists developed a process whereby the surfaces of nanoscale silicon tips are exposed to carbon ions and then annealed so that a strong silicon carbide layer is formed, but the nanoscale sharpness of the original silicon tip is maintained. Although has long been known as an ideal candidate material for such tips, the unique carbon implantation and annealing process made it possible to harden the surface while maintaining the original shape and ensuring strong adhesion between the hardened surface of the tip and the underlying material--similar to how steel is tempered to make it harder.

Consisting primarily of carbon and silicon, the tip is sharpened to a nano-sized apex and integrated on the end of a silicon microcantilever for use in atomic force microscopy. The importance of the development lies not only in its ability to maintain the sharpness of the tip and its resistance to wear, but also in its endurance when sliding against a hard substrate such as . Because silicon--used in almost all integrated circuit devices--oxidizes in the atmosphere, forming a thin layer of its oxide, this system is among the most relevant for emerging applications in nanolithography and nanomanufacturing applications.

More specifically, scientists hope that the new tip can be used to fabricate bio sensors, for example for managing glucose levels in diabetic patients or monitoring pollution levels in water.

Probe-based technologies are expected to play a predominant role in many such technologies. However, poor wear performance of the tip materials used so far, especially when slid against , have previously limited their usefulness for experimental applications.

The next step for scientists is to begin testing the new tip for use in applications, starting with nanomanufacturing.

The study, published today in the peer-reviewed journal Advanced Functional Materials, was conducted collaboratively by Dr. Mark A. Lantz and Dr. Bernd Gotsmann, IBM Research - Zurich; Tevis D. B. Jacobs, Dr. Papot Jaroenapibal, Prof. Robert W. Carpick, University of Pennsylvania; and Sean D. O'Connor and Prof. Kumar Sridharan, University of Wisconsin.

Explore further: Nanotechnologists form near-frictionless diamond material

More information: DOI:10.1002/adfm.201102383

Related Stories

Nanotechnologists form near-frictionless diamond material

February 25, 2010

Researchers at the University of Pennsylvania, the University of Wisconsin-Madison and IBM Research-Zürich have fabricated an ultra sharp, diamond-like carbon tip possessing such high strength that it is 3,000 times more ...

IBM Scientists Effectively Eliminate Wear at the Nanoscale

September 7, 2009

( -- IBM scientists have demonstrated a promising and practical method that effectively eliminates the mechanical wear in the nanometer-sharp tips used in scanning probe-based techniques. This discovery can potentially ...

New nanocrystalline diamond probes overcome wear

November 10, 2009

Researchers at the McCormick School of Engineering and Applied Science at Northwestern University have developed, characterized, and modeled a new kind of probe used in atomic force microscopy (AFM), which images, measures, ...

'Heftier' atoms reduce friction at the nanoscale

November 1, 2007

A research team led by a University of Pennsylvania mechanical engineer has discovered that friction between two sliding bodies can be reduced at the molecular, or nanoscale, level by changing the mass of the atoms at the ...

IBM introduces new graphene transistor

April 11, 2011

( -- In a report published in Nature, Yu-ming Lin and Phaedon Avoris, IBM researchers, have announced the development of a new graphene transistor which is smaller and faster than the one they introduced in February ...

Recommended for you

Atomic blasting creates new devices to measure nanoparticles

December 14, 2017

Like sandblasting at the nanometer scale, focused beams of ions ablate hard materials to form intricate three-dimensional patterns. The beams can create tiny features in the lateral dimensions—length and width, but to create ...

Engineers create plants that glow

December 13, 2017

Imagine that instead of switching on a lamp when it gets dark, you could read by the light of a glowing plant on your desk.

Faster, more accurate cancer detection using nanoparticles

December 12, 2017

Using light-emitting nanoparticles, Rutgers University-New Brunswick scientists have invented a highly effective method to detect tiny tumors and track their spread, potentially leading to earlier cancer detection and more ...

1 comment

Adjust slider to filter visible comments by rank

Display comments: newest first

not rated yet Feb 09, 2012
i remember reading what some consider the major technological developments needed after some recent stm/afm(scanning tunneling microscope) advances(the ability to move and bind single atoms - specificaly silicon atoms). This was one of those major desired developments.

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.