New 'green' technologies make die castings stronger

Apr 17, 2010

Conventional die castings can be made stronger using new, more environmentally friendly technologies developed by CSIRO.

The two new technologies - a dynamic gating system and the 'ATM runner system' - produce high-integrity castings with fine-grained and low porosity by improving the feed of molten metal into the casting. Both systems are suitable for use with aluminium and magnesium alloys.

"This is accomplished by influencing the flow behaviour of the molten metal, the fill pattern of the die, and subsequent solidification," says the leader of CSIRO's research team of metallurgists and casting engineers, Dr Rob O'Donnell.

"Our researchers realised that by changing the way in which molten metal is delivered to the die we could take advantage of the high pressure inherent in the process to make castings with finer microstructure and lower porosity," Dr O'Donnell says.

The researchers achieved higher quality castings by changing the architecture of the runners (the passages along which molten metal flows into the die) and the gate (the narrow opening to the die cavity).

"Our improved melt delivery systems are cost-effective, can be used with existing casting machines, and can significantly reduce the mass of the metal runner, wasting less metal.

"They represent new 'green' die casting technologies, which are low-energy and highly effective."

Gases captured during the passage of the into the die cavity cause porosity, which together with voids created during solidification, reduces the quality of the casting.

Die castings with low porosity are stronger and can be successfully heat treated post-casting to improve their mechanical properties.

The dynamic gating system (DGS) incorporates a gate capable of changing its size in response to the pressure of the melt during filling.
X-ray analysis of test castings showed a significant improvement in density in both thicker and thinner areas of the casting, when the dynamic gate was used.

A paper describing the dynamic gating system received the best paper award at the North American Die Casting Association (NADCA) CastExpo10 congress, held in March in Orlando, Florida.

A reviewer of the paper commended the CSIRO researchers for producing a technology with "real-world" relevance to high pressure die casting, saying "This is a technology that has significant promise in the future of our industry".

ATM technology uses a revolutionary melt delivery system for the high pressure die casting (HPDC) process, which is cheaper to operate than conventional HPDC.

The ATM casting technology has been proven by a number of companies in commercial production, and its effectiveness in reducing both shot weight and reject rates has been demonstrated.

"ATM conditions the melt prior to filling the cavity so that the melt enters the die in a less viscous, 'runnier' state," Dr O'Donnell said.

"As a result, melt flow is improved and separate melt fronts fuse together better when they meet within the casting."

The outcome is a casting with a more uniform distribution of nucleation sites, a refined, homogenous microstructure, and exceptionally low porosity.

Explore further: Lifting the brakes on fuel efficiency

add to favorites email to friend print save as pdf

Related Stories

Heat treatment process supplies stronger die cast parts

Feb 12, 2008

Car components with doubled mechanical strength, higher fatigue resistance and improved energy absorption are the result of a revolutionary CSIRO heat treatment process for high pressure die casting (HPDC) ...

Innovative magnesium sheet production process licensed

Jun 06, 2005

CSIRO has signed an exclusive option to license its magnesium sheet production process with Magnesium International Limited's subsidiary Magnesium International (No 1) Pty Ltd. The CSIRO technology is one of only a few tec ...

Savvy injection molding

Apr 02, 2010

(PhysOrg.com) -- With the help of neural networks, in which complex algorithms are used to monitor critical process steps, engineers are paving the way for zero-defect production in the area of metal powder ...

Recommended for you

Lifting the brakes on fuel efficiency

Apr 18, 2014

The work of a research leader at Michigan Technological University is attracting attention from Michigan's Governor as well as automotive companies around the world. Xiaodi "Scott" Huang of Michigan Tech's ...

Large streams of data warn cars, banks and oil drillers

Apr 16, 2014

Better warning systems that alert motorists to a collision, make banks aware of the risk of losses on bad customers, and tell oil companies about potential problems with new drilling. This is the aim of AMIDST, the EU project ...

User comments : 0

More news stories

Growing app industry has developers racing to keep up

Smartphone application developers say they are challenged by the glut of apps as well as the need to update their software to keep up with evolving phone technology, making creative pricing strategies essential to finding ...

Making graphene in your kitchen

Graphene has been touted as a wonder material—the world's thinnest substance, but super-strong. Now scientists say it is so easy to make you could produce some in your kitchen.