Composite battery boost

Dec 04, 2013 by David Bradley
Composite battery boost
Normalized XANES spectra of Li/Se cell during cycling. Black line is the battery voltage profile.

(Phys.org) —New composite materials based on selenium (Se) sulfides that act as the positive electrode in a rechargeable lithium-ion (Li-ion) battery could boost the range of electric vehicles by up to five times, according to groundbreaking research carried out at the U.S. Department of Energy's Advanced Photon Source at Argonne National Laboratory. The studies of the materials demonstrated that they have the potential to pack five times the energy density of conventional batteries.

Lithium-ion batteries are ubiquitous in rechargeable gadgets such as cell phones, tablet PCs, and GPS devices, as well as early electric vehicles. As any user of these technologies will testify, the amount of charge Li-ion batteries can hold between power outlets can stand improving, and all-electric vehicles in particular will benefit from a longer lasting battery. The problem is that existing electrode materials, while relatively effective, cannot pack much electrical energy into a small volume and so range is limited.

Now, researchers from Argonne and King Abdulaziz University (Saudi Arabia) hope to remedy that problem. They have focused on carbon-selenium sulfide composites as an alternative material to the conventional lithium transition metal oxide positive in standard batteries. These composites are anticipated to have an energy density five times higher than conventional batteries. This could mean up to five times greater range between charging stations.

The researchers point out that in a typical lithium battery, electrical capacity is between 120- and 160-milliamp-hours (mAh) per gram of material. The use of the novel can boost that capacity to around 678-mAh per gram. While such a boost is theoretically very attractive, understanding the nature of the electrochemical changes taking place when these materials are used (instead of conventional lithium-metal oxide electrodes) is vital to ensure they will be viable in future batteries.

Using the X-ray Science Division (XSD) beamline 11-ID-C at the Advanced Photon Source, the team carried out in situ synchrotron high-energy x-ray diffraction (HEXRD) studies and complementary, selenium K-edge x-ray absorption near-edge structure (XANES) analysis to observe the chemical changes that take place in these novel electrode materials as they charge and discharge a battery (see the figure).

These measurements, which were undertaken at more than 12-keV energy, were also done in transmission mode on the XSD bending-magnet beamlines 9-BM-C and 20-BM-B. This technique allowed the team to hone in on the changing chemistry of the selenium atoms in the electrode and how they shift between crystalline and non-crystalline phases as current and lithium ions flow through the experimental battery's ether-based electrolyte. Raman microscopy at Argonne's Center for Nanoscale Materials provided additional information about the Li2Se that was observed on the Li anode of the charged cells.

The power of HEXRD and XAS available on these x-ray beamlines allowed instantaneous monitoring of the phase changes in the electrode materials under charge and discharge states. The team could observe exactly what intermediate stages the materials went through as well as detect their chemical oxidation states. Such details are critical to the development of a new stable electrode material that might be charged and discharged many hundreds, if not thousands, of repetitions in its lifetime.

The team discovered that it is the chemical composition of the electrolyte—the fluid that bathes the electrodes and through which the charge-carrying positive lithium ions flow—that seems to have the most impact on the changes that take place. The researchers suggest it might be possible to tune the efficiency of a battery based on these new composites by optimizing the electrolyte and so improve battery performance still further.

The x-ray studies and analysis of the electrochemistry of the electrode as it operates have also allowed the team to discover a plausible chemical mechanism for the processes involved in discharging the battery. They explain that the composite electrode is reduced to form lithium polyselenide with more than four selenium atoms per lithium atom; additional discharging to lower voltage leads to chemical species containing two lithium ions per selenium atom. Charging involves the reverse process. This mechanism is first proposed and experimentally proven by the team, and it is similar to that seen in experimental lithium-sulfur electrodes.

Explore further: Inexpensive material boosts battery capacity

More information: Yanjie Cui1, Ali Abouimrane1, Jun Lu1, Trudy Bolin1, Yang Ren1, Wei Weng1, Chengjun Sun1, Victor A. Maroni1, Steve M. Heald1, and Khalil Amine1,2, "(De)Lithiation Mechanism of Li/SeSx (x = 0−7) Batteries Determined by in situ Synchrotron X‑ray Diffraction and X‑ray Absorption Spectroscopy," J. Am. Chem. Soc. 135, 8047 (2013). DOI: 10.1021/ja402597g

Related Stories

Inexpensive material boosts battery capacity

Oct 23, 2013

Battery-powered cars offer many environmental benefits, but a car with a full tank of gasoline can travel further. By improving the energy capacity of lithium-ion batteries, a new electrode made from iron ...

Eavesdropping on lithium ions

Jul 08, 2013

(Phys.org) —Lithium ion batteries are at the energetic heart of almost all things tech, from cell phones to tablets to electric vehicles. That's because they are a proven technology, light, long-lasting ...

A nanoscale glimpse of batteries in action

Sep 13, 2013

Lithium–oxygen (Li–O2) batteries are a new type of experimental battery that electric car manufacturers are hoping will address the issue of limited driving range. Unlike the lithium-ion batteries used ...

Recommended for you

Scientists develop pioneering new spray-on solar cells

4 hours ago

(Phys.org) —A team of scientists at the University of Sheffield are the first to fabricate perovskite solar cells using a spray-painting process – a discovery that could help cut the cost of solar electricity.

Free pores for molecule transport

23 hours ago

Metal-organic frameworks (MOFs) can take up gases similar to a sponge that soaks up liquids. Hence, these highly porous materials are suited for storing hydrogen or greenhouse gases. However, loading of many ...

User comments : 2

Adjust slider to filter visible comments by rank

Display comments: newest first

QuixoteJ
5 / 5 (1) Dec 04, 2013
The studies of the materials demonstrated that they have the potential to pack five times the energy density of conventional batteries.
Is it at the expense of power density, though? The link to more info implies a faster charging time which may not mean it sacrifices power density, but we'll see.
Mazarin07
not rated yet Dec 10, 2013
There are so many good news like this one, but no one is introduced in everyday life.