Dynamics of contact electrification

Dynamics of contact electrification
Scheme of the experimental setup. An electric equivalent circuit is displayed in the upper right corner. The charge is “split” between the capacity with the top and the bottom plate. Credit: Science Advances, doi: 10.1126/sciadv.abg7595

A new report on Science Advances developed by Mirco Kaponig and colleagues in physics and nanointegration in Germany, detailed the very basic concept of contact electrification between two metals. In a new experimental method, the researchers followed the charge of a small sphere bouncing on a grounded planar electrode on a timescale down to 1 microsecond. The team noted how the sphere discharged in the moment of contact lasting for 6 to 8 microseconds. At the moment of disruption of the electrical contact, the sphere regained charge far beyond expectations relative to the contact potential difference. The excess charge arose with increasing contact area.

Contact electrification

Contact electrification is a ubiquitous phenomenon that occurs when two surfaces touch. The process is an elementary method of triboelectricity that can be observed directly in daily life. The phenomenon is responsible for lightening in thunderstorms, sandstorms or volcanic plumes. The process can be of major concern when handling potentially explosive liquids or dusts. As a result, researchers have established empirical safety regulations to avoid hazards caused by electric discharges through triboelectric charging. Although the phenomenon was described for more than 2000 years, the underlying mechanisms are still debated. Scientists typically consider three kinds of charge transfer including the transfer of electrons, ions or material with partial charge. In metal-metal contacts, electrons can be transferred between two surfaces to establish contact potential. The amount of transferred charge also depended on the mutual capacity when the electric contact is disrupted, and the observed charge transfer strongly supported the concept of electron transfer for metal-metal contacts. The situation is less obvious for metal-insulator or insulator-insulator contacts. Kaponig et al. therefore presented a new experimental technique to analyze charge transfer during contact electrification, with unprecedented resolution.

Dynamics of contact electrification
Measurement of the charge on the lower plate of the capacitor and derived quantities. (A) The signal measured at the lower plate overlaid to a simulation according to Eqs. 1 and 3. It shows a perfect agreement, except at the very beginning and the top of the first parabola because of the field distortion in the vicinity of the entrance hole, which is not included in the numerical description. On the given scale, the signal noise is barely visible. The histogram in the upper right corner displays the charge on the sphere between the contacts. (B) The vertical position of the sphere bouncing on the plate derived from the contact times. (C) The potential calculated according to Eq. 4. in the study reveals that the sphere may reach a voltage of up to 10 V. Credit: Science Advances, doi: 10.1126/sciadv.abg7595

The experiments

The work revealed how the electric potential of a metallic particle bouncing from a metallic surface evolved with time. Based on the outcomes, Kaponig et al. noted how the charge increased with impact velocity in metal-metal contacts; a feature commonly observed with metal-insulator and insulator-insulator contacts but hither to unobserved for metal-metal contacts. During the experiments, this led to unexpectedly high electric potentials for purely metallic contacts. Since the electric contact was only established for a few microseconds during mechanical contact, the process did not retain the parameters of the charge before contact. The potential of the sphere was therefore only reduced to the contact potential of a few tenths of a volt. When the electric contact detached from the surface, however, the charge on the sphere established a potential of up to 3 V for less than 1 microsecond.

Charge transfer

Dynamics of contact electrification
Details of the first and second contact from about 100 μs before and 100 μs after the contact. (A) The measured and simulated charge as well as the derived potential for the first contact. The deviation marked by * is due to the “mechanical response” of the plate after the impact of the sphere. The horizontal line corresponds to the initial charge of the sphere or the zero point of the potential. The dashed vertical lines indicate the time interval of the mechanical contact. The plateau of the signal corresponds to the electrical contact. The insets sketch the charge distribution on the sphere and the plates. The relative size of the sphere is strongly exaggerated. The deformation is schematic; in reality, both the sphere and the surface are deformed. (B) The corresponding height of the sphere. The motion before and after the contact is almost linear on the short time scale. (C) The calculated capacity before and after the contact by the green line. During the contact, a tentative value proportional to the contact area is sketched by the dashed red line. The arrow points to the value of the capacity at the very moment when the electric contact is broken. It is assumed that the capacity is enhanced relative to the ideal geometry because of the deformation of the contact area by creating relatively large adjacent surfaces. (D) The measured and calculated charge as well as the derived potential for the second contact. Credit: Science Advances, doi: 10.1126/sciadv.abg7595

Scientists had previously studied the charge transfer of particles bouncing on an inclined surface based on contact-free electrostatic detection. Kaponig et al. therefore developed an experimental scheme to measure the charge before and after surface contact to follow the dynamics in real-time. In the setup, they obtained a resolution better than 1 microsecond in time for about 6000 electrons. They studied the motion and contact electrification by dropping gold spheres that are 1 mm in diameter through a small orifice into a parallel plate capacitor. The spheres bounced on a virtually grounded lower plate, allowing the scientists to measure the induced and transferred charges. The team performed the experiments in vacuum. The signal detected at the lower plate of the setup had two contributions including the charge on the sphere and the charge transferred to the sphere. The team noted the display signal of a gold sphere bouncing more than 15 times on the lower plate of the capacitor made of copper, the trajectory of the sphere consisted of segments of free fall, starting and completing via contact with the plate.

When Kaponig et al. closely inspected the signal, they identified the moments of contact by abrupt changes of the measured charge. They noted how the time spent between two contacts determined the segment of the trajectory. The team next applied a voltage at the ramp to guide the sphere to the entrance of the capacitor, where the sphere was positively charged before it entered the capacitor and became negatively charged during the first contact. The observed magnitude of the charge was unexpectedly high. The researchers then repeated the experiment with different initial charges, where the sphere became negatively charged at the first and following contact. Another key to understand contact electrification included the potential of the sphere. Based on the high magnitude of the charge on the sphere, the team noted a potential of several volts unexpectedly high for a purely metallic system. The electric contact was only established as a mechanical contact for a few microseconds. The potential of the sphere was therefore reduced to the contact potential of a few tenths of a volt. As the distance between the sphere and plate grew, the potential further increased.

Outlook

The team described the observations using a metal-contact model in which the raised for the first-contact, followed by an enormous capacity formed at the interface due to the minimal distance between the charges. This capacity charged to the contact potential in the order of picocoulombs. Upon contact break, the two adjacent surfaces of the plate and sphere fit almost snugly to form a large area at close separation and a larger capacity, where the size of the area depended on the velocity of the sphere. In this way, Mirco Kaponig and colleagues showed how a metallic sphere bouncing from a metal plate achieved a potential of up to 10 V, due to a deformation of the contact area. This led to an increased capacity between the and the plate upon electric contact disruption. The results are important for contact electrification and triboelectricity for enhanced charge transfer.

More information: Kaponig M. et al. Dynamics of contact electrification, Science Advances, DOI: 10.1126/sciadv.abg7595

Baytekin H. T. et al. The mosaic of surface charge in contact electrification, Science, 10.1126/science.1201512

Gimzewski J. K. et al. Transition from the tunneling regime to point contact studied using scanning tunneling microscopy, Physical Review B, doi.org/10.1103/PhysRevB.36.1284

© 2021 Science X Network

Citation: Dynamics of contact electrification (2021, June 9) retrieved 19 March 2024 from https://phys.org/news/2021-06-dynamics-contact-electrification.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

Explore further

A levitated nanosphere as an ultra-sensitive sensor

19 shares

Feedback to editors