High color purity 3-D printing

High color purity 3D printing
Laser sintered samples by using PA12 powder and gold nanoparticles (GNRs), tungsten oxide (WO3) and carbon-black-based sensitizers (CB). Credit: ICFO

Selective powder sintering for 3-D printing has recently become an increasingly affordable solution for manufacturing made-to-order elements of almost any shape or geometry. This technique involves heating a bed of powder (such as polyamide, PA12) to just below its melting point, using an IR light source to selectively melt a cross section of the powder, then adding more powder and repeating to form a 3-D object. To reduce costs and increase printing speed, a photothermal sensitizer is often added to the powders. Typically carbon-based, with a strong broadband absorption, adding these sensitizers to the polymer powders increases the conversion of incident light to heat, which means greater print speeds. However, carbon-based sensitizers can only produce black or gray objects. To create white or colorful prints, visibly transparent equivalents are needed.

A study conducted a few years ago by a team of researchers at ICFO, first authored by Alexander Powell and led by ICREA Professors at ICFO Gerasimos Konstantatos, and Romain Quidant, reported on a solution for overcoming color restrictions in this method using . The researchers designed gold coated with silica as a photothermal sensitizer to allow a rapid sintering of polymer powders into 3-D objects by having these nanoparticles strongly absorb in the near-infrared, while only minimally interacting with visible light. At resonance, these composites showed greatly improved light-to-heat conversion compared with equivalent composites and could be sintered using low-power light sources. While these particles showed to be very efficient for the rapid fabrication of colored 3-D objects, they proved to have certain limitations when trying to print 3-D objects in pure white color or multicolor with high color fidelity across a large hue range affecting the quality of the coloration of prints in high concentrations.

Thus, in a recent study published in Nano Letters, the ICFO researchers Alexander Powell, Alexandros Stavrinadis, and Sotirios Christodoulou, led by ICREA Professors at ICFO Gerasimos Konstantatos, and Romain Quidant, have now reported on the use a new that has proven to easy overcome these problems.

In their study, the team of researchers has reported on using nanoparticles made of tungsten oxide (WO3) as the photothermal sensitizers for polymer powders. These nanoparticles comprise low cost elements, which make them easy and cheap to fabricate. They are colorless at high concentrations and have a strong absorption in the near infrared region, proving their capability of turning light into heat at a fast rate, and thus enabling them as fast fusing agents. In addition, they can be efficiently turned on or off with electricity or ultraviolet radiation. Even more, they are stable at very high temperatures and demonstrate a heating-to-color change rate superior when compared to other available sensitizers. Finally, when mixed with other color inks, these nanoparticles have been able to reproduce the same shades of color as the original powders, maintaining the color purity of the pristine samples.

The results of the study open a new pathway for the use of plasmonic nanoparticles that can be used to produce high color quality 3-D-multicolor objects for advanced manufacturing processes.


Explore further

Fast, cheap and colorful 3-D printing

More information: Alexander W. Powell et al. On-Demand Activation of Photochromic Nanoheaters for High Color Purity 3D Printing, Nano Letters (2020). DOI: 10.1021/acs.nanolett.0c00414
Journal information: Nano Letters

Provided by ICFO
Citation: High color purity 3-D printing (2020, May 7) retrieved 4 June 2020 from https://phys.org/news/2020-05-high-purity-d.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.
21 shares

Feedback to editors

User comments