Movable microplatform floats on a sea of droplets (w/ video)

December 16, 2016 by David L. Chandler
New MIT research could offer a way of making tiny movable parts with no solid connections between the pieces, potentially eliminating a major source of wear and failure in microelectromechanical machines. The new system uses a layer of liquid droplets to support a tiny, movable platform. Credit: Daniel Preston/Device Research Lab

Microelectromechanical systems, or MEMS, are tiny machines fabricated using equipment and processes developed for the production of electronic chips and devices. They've found a wide variety of applications in today's consumer electronics, but their moving parts can wear out over time as a result of friction.

A new approach developed by researchers at MIT could offer a new way of making movable parts with no solid connections between the pieces, potentially eliminating a major source of wear and failure.

The new system uses a layer of to support a tiny, movable , which essentially floats on top of the droplets. The droplets can be water or some other fluid, and the precise movements of the platform can be controlled electrically, through a system that can alter the dimensions of the droplets to raise, lower, and tilt the platform.

The new findings are reported in a paper in Applied Physics Letters, co-authored by Daniel Preston, an MIT graduate student; Evelyn Wang, the Gail E. Kendall Associate Professor of Mechanical Engineering; and five others.

Preston explains that the new system could be used to make devices such as stages for microscope specimens. The focus of the microscope could be controlled by raising or lowering the stage, which would involve changing the shapes of supporting liquid droplets.

The video will load shortly
A new approach to microelectromechanical systems (MEMS), developed by a team of researchers at MIT, could offer a new way of making movable parts with no solid connections between the pieces, potentially eliminating a major source of wear and failure. Credit: Melanie Gonick/MIT

The system works by altering the way the droplets interact with the below them, governed by a characteristic known as the contact angle. This angle is a measure of how steep the edge of the droplet is at the point where it meets the surface. On hydrophilic, or water-attracting, surfaces, droplets spread out nearly flat, producing a very small contact angle, while hydrophobic, or water-repelling, surfaces cause droplets to be nearly spherical, barely touching the surface, with very large contact angles. On certain kinds of dielectric surfaces, these qualities can be "tuned" across that whole range by simply varying a voltage applied to the surface.

As the surface gets more hydrophobic and the droplets get rounder, their tops rise farther from the surface, thus raising the platform—in these tests, a thin sheet of copper—that floats on them. By selectively changing different droplets by different amounts, the platform can also be selectively tilted. This could be used, for example, to change the angle of a mirrored surface in order to aim a laser beam, Preston says. "There are a lot of experiments that use lasers, that could really benefit from a way to make these small-scale movements."

The new system could be used to make devices such as stages for microscope specimens. The focus of the microscope could be controlled by raising or lowering the stage, which would involve changing the shapes of supporting liquid droplets. Credit: Daniel Preston/Device Research Lab

In order to maintain the positioning of the droplets rather than letting them slide around, the team treated the underside of the floating platform. They made the overall surface hydrophobic, but with small circles of hydrophilic material. That way, all the are securely "pinned" to those water-attracting surfaces, keeping the platform securely in position.

In the group's initial test device, the vertical positioning can be controlled to within a precision of 10 microns, or millionths of a meter, over a range of motion of 130 microns.

MEMS devices, Preston says, "often fail when there's a solid-solid contact that wears out, or just gets stuck. At these very small scales, things break down easily."

While the basic technology behind the alteration of droplet shapes on a surface is not a new idea, Preston says, "nobody has used it to move a stage, without any solid-solid contact. The real innovation here is being able to move a stage up and down, and change its angle, without any solid material connections."

In principle, it would be possible to use a large array of electrodes that could be adjusted to move a platform across a surface in precise ways, in addition to up and down. For example, it could be used for "lab on a chip" applications, where a biological sample could be mounted on the platform and then moved around from one test site to another on the microchip.

He says the system is relatively simple to implement and that it would be possible to develop it for specific real-world application fairly rapidly. "It depends how motivated people are," he says. "But I don't see any huge barriers to large-scale use. I think it could be done within a year."

The research team included MIT graduate students Ariel Anders and Yangying Zhu, Research Affiliate Banafsheh Barabadi, alumna Evelyn Tio '14, and undergraduate student DingRan Dai. The work was supported by the Office of Naval Research and the National Science Foundation.

Explore further: Temperature difference propels droplets

Related Stories

Temperature difference propels droplets

October 14, 2016

Researchers at MIT and elsewhere have developed a new way of driving fluid droplets across surfaces in a precisely controlled way. The method could open up new possibilities for highly adaptable microfluidic devices, as well ...

Small droplets feel the vibe

October 6, 2016

A team of researchers at the University of Bristol have used ultrasonic forces to accurately pattern thousands of microscopic water-based droplets. Each droplet can be designed to perform a biochemical experiment, which could ...

New surface makes oil contamination remove itself

June 17, 2016

Researchers of Aalto University have developed surfaces where oil transports itself to desired directions. Researchers' oleophobic surfaces are microtextured with radial arrays of undercut stripes. When oil drops fall on ...

Researchers identify movement of droplets on soft surfaces

August 5, 2015

Researchers from the University of Twente have succeeded in clearly identifying why droplets on soft, squishy surfaces react differently than on hard surfaces. A water droplet, for example, moves very differently over jelly ...

Explained: Hydrophobic and hydrophilic

July 16, 2013

Sometimes water spreads evenly when it hits a surface; sometimes it beads into tiny droplets. While people have noticed these differences since ancient times, a better understanding of these properties, and new ways of controlling ...

Recommended for you

Sci-fi holograms a step closer with tiny invention

January 24, 2017

Australian National University physicists have invented a tiny device that creates the highest quality holographic images ever achieved, opening the door to imaging technologies seen in science fiction movies such as Star ...

Modeling the rhythmic electrical activities of the brain

January 24, 2017

Researchers studying the brain have long been interested in its neural oscillations, the rhythmic electrical activity that plays an important role in the transmission of information within the brain's neural circuits. In ...

Camera able to capture imagery of an optical Mach cone

January 23, 2017

(Phys.org)—A team of researchers at Washington University in St. Louis has built a camera apparatus capable of capturing moving imagery of an optical Mach cone. In their paper published in the journal Science Advances, ...

0 comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.