Direct observation of graphene decoupling on Cu(111)

September 20, 2016, Ulsan National Institute of Science and Technology
The decoupling of a graphene nanoribbon, showing the chemical reactions of oxygen and water that led to the surface oxidation at the nanoribbon edge sites. The functionalized nanoribbon edges facilitate the molecular dissociation of oxygen and water that serve as the first stage of oxidation. Credit: Ulsan National Institute of Science and Technology

A recent quantum mechanical study of graphene by a research team at Ulsan National Institute of Science and Technology (UNIST), South Korea, has elucidated the intercalation mechanism and pathways for graphene decoupling from the copper substrate.

The films, grown on the copper (Cu) substrates must be detached clean without leaving residue behind, as residual metallic impurities can significantly alter electronic and electrochemical properties of graphene.

However, thanks to recent advances in graphene transfer method, the electrochemical corrosion of graphene coatings on Cu has allowed the monolayer-thick material to be mechanically delaminated without significantly compromising its structural integrity.

The new UNIST graphene research veers off in a new direction by succesfully seperating graphene from its metal growth substrates without the assistance of the adhesive tape. The research findings have been published in the August issue of the Journal of the American Chemical Society (JACS).

In the study, led by Prof. Sang Kyu Kwak (School of Energy and Chemical Engineering) and Prof. Rodney Ruoff (Center for Multidimensional Carbon Materials), the research team revealed the surface oxidation chemistry of the nanoribbon-covered Cu(111) surface.

Specifically, they have demonstrated that the graphene nanoribbon (GNR) edge type influences the initial oxidation stages of the Cu surface, thus driving the nanoribbon decoupling by the intercalation of surrounding adsorbate molecules (e.g. oxygen and water).

The difference between the armchair GNR and zigzag GNR on the Cu(111) substrate, is distinguished by the presence of an edge state in the zigzag GNR edges, which has been attributed to the hybridization between the out-of-plane carbon π orbitals and the metal d orbitals. This edge state, however, is absent in the armchair GNR edge atoms. Such an observation has not been reported for H-terminated GNR on Cu(111).

Vibrational stretching mode calculations showed that the GNR edges influenced the molecular adsorption of oxygen at the bare and GNR/Cu sites, confirming the role of GNR edges in weakening the pre-elongated O-O bond at the GNR/Cu interface. The research team also explained that the GNR edges facilitated the stabilization of water molecules (regardless of surface oxygenation), which would otherwise be unstable on the bare Cu surface.

Dr. Kester Wong, who takes full charge of the research, notes that "GNR-mediated interactions between water and the chemisorbed oxygen radicals can shed further light in elucidating the role of water and oxygen in the surface oxide formation."

"This particular study may have interesting implications for the development of regioselective graphene-based catalysis. Nonetheless, employing other crystal facets for the interfacial study of low dimensional materials is of great interest, and several investigations are being heavily pursued by our group in this area", says Prof. Kwak.

Explore further: Molecular self-assembly controls graphene-edge configuration

More information: Kester Wong et al. First-Principles Study of the Role of Oand HO in the Decoupling of Graphene on Cu(111), Journal of the American Chemical Society (2016). DOI: 10.1021/jacs.6b05333

Related Stories

Molecular self-assembly controls graphene-edge configuration

September 10, 2014

A research team headed by Prof. Patrick Han and Prof. Taro Hitosugi at the Advanced Institute of Materials Research (AIMR), Tohoku University discovered a new bottom-up fabrication method that produces defect-free graphene ...

Porphyrins can be covalently attached to graphene edges

September 12, 2016

(Phys.org)—Researchers from Technische Universität München in Germany have succeeded in covalently binding porphine to the edge of a graphene sheet on a Ag(111) substrate using surface-assisted covalent coupling. This ...

Recommended for you

0 comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.