New method provides direct SI traceability for sound pressure

April 28, 2015, National Physical Laboratory
The new technique uses laser beams that intersect at a point to produce an interference fringe volume. Credit: NPL

Scientists at the National Physical Laboratory (NPL) - the UK's National Measurement Institute - have developed an optical method for remotely measuring sound pressure inside a fully anechoic chamber which is the first to provide direct traceability to the SI base units.

Accurate measurements of airborne sound are needed for a range of regulatory, health and safety, and commercial applications, from monitoring environmental noise to testing the performance of acoustic devices. To ensure reliable measurements of , microphones must be regularly calibrated by measuring their sensitivity over a certain frequency range.

Currently, the most accurate method for calibrating microphones is based on the principle of reciprocity - a theory first conceived by Lord Rayleigh nearly 150 years ago. However, this method can only be used to calibrate a limited number of microphones of specific types and dimensions, and cannot be applied to new types of device such as microelectromechanical systems (MEMS). The unit of sound pressure, the pascal, is also currently determined indirectly through assumptions on the propagation characteristics of sound and the dimensions of the device being tested.

Researchers at NPL have developed a new optical method for directly measuring sound pressure. The method can be used to determine the sensitivity of any acoustic device with direct traceability to length standards, and without assumptions regarding the geometry and sound field characteristics.

The method, published in the journal Applied Physics Letters, is based on an optical technique known as . Two laser beams are crossed to form an interference fringe volume - the pattern caused by the interaction of the two waves. Sound waves are emitted by a source within the test chamber, causing airborne particles to oscillate. As the oscillating particles cross the interference fringes, they scatter photons, which can be detected by a single photon counter. From this, the particle velocities can be measured in a direct and absolute manner and are used to determine the pressure. By repeating the procedure at a range of different emitted frequencies, can be calibrated directly against the acoustic unit of sound pressure.

The optical method can form the basis of a future primary standard for sound pressure measurement which is directly traceable to the SI base units. An extensive theoretical and experimental study of the sources of uncertainty would be needed prior to the introduction of such a standard, and this work is currently underway.

Explore further: A new generation of acoustic measurements

Related Stories

A new generation of acoustic measurements

May 29, 2012

NPL scientists have made the first measurements of airborne acoustic free-field pressures using a laser technique based on photon correlation spectroscopy.

Weighing gas with sound and microwaves

January 26, 2015

NIST scientists have developed a novel method to rapidly and accurately calibrate gas flow meters, such as those used to measure natural gas flowing in pipelines, by applying a fundamental physical principle: When a sound ...

Acoustic levitation made simple

January 5, 2015

A team of researchers at the University of São Paulo in Brazil has developed a new levitation device that can hover a tiny object with more control than any instrument that has come before.

Engineering students use sound waves to put out fires

March 26, 2015

Two engineering students at George Mason University have found a way to use sound waves to quash fires and have built a type of extinguisher using what they have learned that they hope will revolutionize fire fighting technology. ...

Recommended for you

Rapid and continuous 3-D printing with light

January 22, 2019

Three-dimensional (3-D) printing, also known as additive manufacturing (AM), can transform a material layer by layer to build an object of interest. 3-D printing is not a new concept, since stereolithography printers have ...

Scientists discover new quantum spin liquid

January 22, 2019

An international research team led by the University of Liverpool and McMaster University has made a significant breakthrough in the search for new states of matter.

Researchers capture an image of negative capacitance in action

January 21, 2019

For the first time ever, an international team of researchers imaged the microscopic state of negative capacitance. This novel result provides researchers with fundamental, atomistic insight into the physics of negative capacitance, ...

Toward ultrafast spintronics

January 21, 2019

Electronics have advanced through continuous improvements in microprocessor technology since the 1960s. However, this process of refinement is projected to stall in the near future due to constraints imposed by the laws of ...


Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.