Fujitsu Develops Millimeter-Wave Gallium-Nitride Transceiver Amplifier Chipset

September 30, 2009
Newly-developed chipset featuring GaN-based high-output transmitter amplifier and high-sensitivity receiver amplifier

Fujitsu announced today the development of the world's first gallium-nitride HEMT-based transceiver amplifier chipset for broadband wireless transmission equipment operating in the millimeter bandwidth, the range of 70 to 100 GHz, for which widespread usage is expected to grow. The new transceiver amplifier chipset features a GaN HEMT-based high-output transmitter amplifier and high-sensitivity receiver amplifier.

The transmitter amplifier achieves the world's highest level of performance with output of 350 mW, while the receiver amplifier features the world's highest level of signal gain at 310 times (310x) operating in the W-band with a low noise figure of 3.8 decibels (dB). Compared to (GaAs)-based technology, the new GaN HEMT-based amplifier chipset for the millimeter band is anticipated to offer output that is increased by approximately four-fold, and a noise figure decreased by 40%, while transmission ranges are expected to be extended by roughly three-fold.

Used as an alternative to fiber-optic cabling, Fujitsu's new GaN HEMT-based millimeter-band transceiver amplifier will help bridge the digital divide for wireless communications, by making communications equipment for trunk lines and ultra-high-speed fixed wireless access higher in quality and more compact, ultimately making wireless broadband more practical.

Details of this technology were presented at the European Microwave Integrated Circuits Conference (EuMIC), being held from September 28 to 29 in Rome. Part of this research was conducted as part of the Research and Development Project for Expansion of Radio Spectrum Resources sponsored by Japan's Ministry of Internal Affairs and Communications.

Cross-section diagram of newly-developed high breakdown-voltage millimeter-wave GaN HEMT integrated circuit

In order to accommodate the demands for greater bandwidth on the Internet, mobile phone networks, and other networks, fiber-optic cabling is being laid throughout Japan to create a high-capacity trunk-line system. This is problematic in heavily built-up areas, or areas with difficult topography, which has sparked interest in high-bandwidth wireless that is capable of data transmission capacities and speeds of 10 Gbps - on par with fiber-optic cabling - as a way to bridge the digital divide.

The millimeter-wave band from 70 to 100 GHz would be an effective band to use for wireless communications running faster than 10 Gbps, as it is readily available and is appropriate for long-distances transmissions. Fujitsu and Fujitsu Laboratories have successfully tested millimeter-band transmitters and receivers at speeds of 10 Gbps using impulse radio. In order for this to be practical and widely used, transmission distances would need to be extended from several kilometers to several tens of kilometers. One way to achieve that would be through higher-output amplifiers. However, higher outputs bring with them increased power-leakage from the transmitter to the receiver, which can overload the inputs of circuits using existing indium-phosphide (InP)- and GaAs-based technologies, resulting in breakdowns. As a result, there has been a desire to develop GaN-based receiver amplifiers, as they can tolerate higher inputs and have excellent reception sensitivity.

In order to enable a transceiver amplifier that satisfies the aforementioned requirements for W-band signals, the following issues need to be addressed:

1. Compared to conventional GaAs HEMT devices, material used in GaN HEMT devices have wide band-gap characteristics that enable breakdown-voltages that are ten times greater, allowing GaN HEMT devices to tolerate higher voltages. However, because the parasitic capacitance of transistors worsens with high-frequency signals of 70 GHz or higher, the signal amplification rate to magnify weak incoming signals - to enable them to be identified - is insufficient, as the incoming signals become buried in noise.

2. At frequencies above 70 GHz, the signal wavelength is roughly the same length as the chip size, which produces signal interference that is more prominent, between signal paths and circuits. This makes it difficult to create an integrated circuit featuring good signal amplification and low noise, due to the fact that oscillation of the circuit itself can result in malfunctions caused by unnecessary power-coupling between the signal paths.

Comparison of millimeter-wave receiver amplifier performance (world's first report for GaN-based)

Fujitsu has addressed the aforementioned issues through the following technologies:

1. Technology for GaN HEMT-based circuits featuring high breakdown-voltage and adapted for millimeter wave

In 2006, Fujitsu and Fujitsu Laboratories developed a GaN HEMT structure with gates of only 0.12 µm in length, allowing for both high breakdown-voltage and good high-frequency performance. By tuning this gate structure and adjusting the thickness of the protective layer, parasitic capacitance was reduced, and the increased signal gain further improved noise characteristics.

2. Millimeter-wave circuit stabilization technology

Compared to existing devices, as the output of GaN HEMTs is higher, signal interference - caused by unnecessary signal emissions from signal circuitry - between signal paths and circuits is more prominent in GaN HEMTs. With the newly-developed device, by laying contact conductors around the signal circuitry, while employing a 3-D electromagnetic field analysis to optimize the placement of via-holes that penetrate the top and bottom of the chip relative to signal paths and circuits, and in addition by developing a design technology that shields against unnecessary signal radiation , and applying all of these for the first time ever in GaN HEMT circuitry, signal interference was successfully suppressed. These technologies realize a circuit that features high output and high signal-gain while being able to operate stably, free from malfunctions caused by circuit oscillations.

The aforementioned technologies have been used to develop a transceiver amplifier chipset for use in millimeter-wave wireless equipment. The newly-developed receiver-amplifier operates in the W-band with a signal gain rate of 25 dB (signal gain is 310x) and a noise figure of 3.8 dB, both figures being the world's best-ever reported for a GaN-based integrated circuit. The amplifier unit's reception performance is on par with those using GaAs-based technology, but because it obviates the need for a protective circuit, the performance of the transceiver as a whole can be expected to improve. In addition, the transmitting amplifier has world-class performance, featuring transmission output of 350 mW.

Compared to GaAs-based technology, the new technology produces output that is roughly four times greater and reduces the noise figure by 40%. Compared to transceivers based on conventional GaAs technology, transmission ranges can be expected to be three times as great. This will pave the way for wireless transmission equipment that is more compact and which features improved transmission quality.

Source: Fujitsu

Explore further: Fujitsu Develops C- to X- Ultra-Wideband Gallium-Nitride HEMT Power Amplifier Featuring High Output and Efficiency

Related Stories

Gallium Nitride Power Transistor for Wireless Base Stations

January 12, 2005

According to JCN Network, Oki Electric has announced that it has started sample provisioning of it's Gallium Nitride High Electron Mobility Transistor (GaN-HEMT), a high frequency wave power transistor for wireless base stations. The ...

Recommended for you

Your (social media) votes matter

January 24, 2017

When Tim Weninger conducted two large-scale experiments on Reddit - otherwise known as "the front page of the internet" - back in 2014, the goal was to better understand the ripple effects of malicious voting behavior and ...

Protective wear inspired by fish scales

January 24, 2017

They started with striped bass. Over a two-year period the researchers went through about 50 bass, puncturing or fracturing hundreds of fish scales under the microscope, to try to understand their properties and mechanics ...

'Droneboarding' takes off in Latvia

January 22, 2017

Skirted on all sides by snow-clad pine forests, Latvia's remote Lake Ninieris would be the perfect picture of winter tranquility—were it not for the huge drone buzzing like a swarm of angry bees as it zooms above the solid ...

Singapore 2G switchoff highlights digital divide

January 22, 2017

When Singapore pulls the plug on its 2G mobile phone network this year, thousands of people could be stuck without a signal—digital have-nots left behind by the relentless march of technology.

Making AI systems that see the world as humans do

January 19, 2017

A Northwestern University team developed a new computational model that performs at human levels on a standard intelligence test. This work is an important step toward making artificial intelligence systems that see and understand ...

1 comment

Adjust slider to filter visible comments by rank

Display comments: newest first

not rated yet Oct 01, 2009
Millimeter waves, like microwaves and lasers, are strictly line of sight. Existing microwave towers might be useful, however, my experience with laser communications showed that the sending unit has to be positioned rock-solid or else the signal moves off the target receiver with thermal expansion, wind, vibration, etc. The beam can be allowed to spread more, to keep some part of the beam on target when the sender moves, but then the power on the target drops, and the distance of transmission is reduced accordingly.

intelligent adaptive targeting schemes exist for lasers, so this problem might be overcome.

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.