Graphene Outperforms Carbon Nanotubes for Creating Stronger, More Crack-Resistant Materials

Apr 26, 2010
New studies by Professor Nikhil Koratkar show graphene outperforms carbon nanotubes and other nanoparticles for boosting the strength and mechanical performance of epoxy composites. Pictured are graphene platelets that Koratkar's research team extracted from bulk graphite.

(PhysOrg.com) -- Three new studies from researchers at Rensselaer Polytechnic Institute illustrate why graphene should be the nanomaterial of choice to strengthen composite materials used in everything from wind turbines to aircraft wings.

Composites infused with graphene are stronger, stiffer, and less prone to failure than composites infused with carbon nanotubes or other nanoparticles, according to the studies. This means graphene, an atom-thick sheet of carbon atoms arranged like a nanoscale chain-link fence, could be a key enabler in the development of next-generation nanocomposite materials.

“I’ve been working in for 10 years, and graphene is the best one I’ve ever seen in terms of ,” said Nikhil Koratkar, professor in the Department of Mechanical, Aerospace, and Nuclear Engineering at Rensselaer, who led the studies. “Graphene is far superior to carbon nanotubes or any other known nanofiller in transferring its exceptional strength and mechanical properties to a host material.”

Results of Koratkar’s studies are detailed in three recently published papers: “Fracture and Fatigue in Graphene Nanocomposites,” published in Small; “Enhanced Mechanical Properties of Nanocomposites at Low Graphene Content,” published in ACS Nano; and “Buckling Resistant Graphene Nanocomposites,” published in the journal .

Advanced composites are increasingly a key component in the design of new windmill blades, aircraft, and other applications requiring ultra-light, high-strength materials. Epoxy composite materials are extremely lightweight, but can be brittle and prone to fracture. Koratkar’s team has infused the advanced composites with stacks, or platelets, of graphene. Each stack is only a few nanometers thick. The research team also infused epoxy composites with carbon nanotubes.

Epoxy materials infused with graphene exhibited far superior performance. In fact, adding graphene equal to 0.1 percent of the weight of the composite boosted the strength and the stiffness of the material to the same degree as adding carbon nanotubes equal to 1 percent of the weight of the composite. This gain, on the measure of one order of magnitude, highlights the promise of graphene, Koratkar said. The graphene fillers also boosted the composite’s resistance to fatigue crack propagation by nearly two orders of magnitude, compared to the baseline epoxy material.

Though graphene and carbon nanotubes are nearly identical in their chemical makeup and mechanical properties, graphene is far better than carbon nanotubes at lending its attributes to a material with which it’s mixed.

“Nanotubes are incredibly strong, but they’re of little use mechanically if they don’t transfer their properties to the composite,” Koratkar said. “A chain is only as strong as its weakest link, and if that link is between the nanotube and the polymer, then that is what determines the overall mechanical properties. It doesn’t matter if the nanotubes are super strong or super stiff, if the interface with the polymer is weak, that interface is going to fail.”

Koratkar said graphene has three distinct advantages over carbon nanotubes. The first advantage is the rough and wrinkled surface texture of graphene, caused by a very high density of surface defects. These defects are a result of the thermal exfoliation process that the Rensselaer research team used to manufacture bulk quantities of graphene from graphite. These “wrinkly” surfaces interlock extremely well with the surrounding polymer material, helping to boost the interfacial load transfer between graphene and the host material.

The second advantage is surface area. As a planer sheet, graphene benefits from considerably more contact with the polymer material than the tube-shaped carbon nanotubes. This is because the polymer chains are unable to enter the interior of the nanotubes, but both the top and bottom surfaces of the graphene sheet can be in close contact with the polymer matrix.

The third benefit is geometry. When microcracks in the composite structure encounter a two-dimensional graphene sheet, they are deflected, or forced to tilt and twist around the sheet. This process helps to absorb the energy that is responsible for propagating the crack. Crack deflection processes are far more effective for two-dimensional sheets with a high aspect ratio such as graphene, as compared to one-dimensional nanotubes.

Koratkar said the aerospace and wind power industries are seeking new materials with which to design stronger, longer-lived rotor and wind turbine blades. His research group plans to further investigate how graphene can benefit this goal. Graphene shows great promise for this because it can be produced from graphite, which is available in bulk quantities and at relatively low cost, he said, which means mass production of is likely to be far more cost effective than nanotubes.

Co-authors on the three papers include Rensselaer mechanical engineering graduate students Mohammed A. Rafiee, Javad Rafiee, and Iti Srivastava; as along with Professor Zhong-Zhen Yu’s group at the Beijing University of Chemical Technology.

Explore further: Understanding the source of extra-large capacities in promising Li-ion battery electrodes

More information: For more information on Koratkar’s research, visit: www.rpi.edu/~koratn .

Related Stories

Unzipping Carbon Nanotubes Can Make Graphene Ribbons

Apr 20, 2009

(PhysOrg.com) -- By "unzipping" carbon nanotubes, researchers have shown how to make flat graphene ribbons. Graphene, which is a one-atom-thick sheet of carbon that looks like chicken wire, has unique electrical ...

Light-speed nanotech: Controlling the nature of graphene

Jan 21, 2009

Researchers at Rensselaer Polytechnic Institute have discovered a new method for controlling the nature of graphene, bringing academia and industry potentially one step closer to realizing the mass production ...

Producing graphene layers using crystallization

Mar 02, 2010

(PhysOrg.com) -- Ever since it's relatively recent discovery, graphene has generated a great deal of interest. Graphene is extracted from graphite in many cases, and consists of a sheet of carbon atoms bound together in a ...

Recommended for you

Tough foam from tiny sheets

27 minutes ago

Tough, ultralight foam of atom-thick sheets can be made to any size and shape through a chemical process invented at Rice University.

Graphene surfaces on photonic racetracks

Jul 28, 2014

In an article published in Optics Express, scientists from The University of Manchester describe how graphene can be wrapped around a silicon wire, or waveguide, and modify the transmission of light through it.

Simulating the invisible

Jul 28, 2014

Panagiotis Grammatikopoulos in the OIST Nanoparticles by Design Unit simulates the interactions of particles that are too small to see, and too complicated to visualize. In order to study the particles' behavior, he uses ...

Building 'invisible' materials with light

Jul 28, 2014

A new method of building materials using light, developed by researchers at the University of Cambridge, could one day enable technologies that are often considered the realm of science fiction, such as invisibility ...

User comments : 1

Adjust slider to filter visible comments by rank

Display comments: newest first

210
1 / 5 (1) Apr 26, 2010
'Bloodoflamb' please respond if you are out here:

I found this article most fascinating...but,...
I did NOT see the words 'ALLOY' or 'DOPANT/DOPING".
SO what kind of material mixture is being discussed relevant to what we have had in metals and ceramics, etc.
IS a metal still a metal with graphene as a strengthening component?
If garphene is 'put' into a compound/structure bearing electron deficient metals or groups, does it reinforce the properties mentioned in the above article? Have we made a better medium into which a carbon based substance can and has been added?

TrustTheONE
Apr 27, 2010
This comment has been removed by a moderator.