Assuring quality in lightweight construction

Oct 21, 2009

Aerospace, automotive and airplane construction count on lightweight construction. But to make sure that lightening the load does not come at the cost of safety, Fraunhofer researchers are working on new quality assurance systems for material testing. At the Composites Europe trade show in Stuttgart, Germany, they will demonstrate a new kind of non-destructive diagnostic procedure.

Boats, airplanes and spacecrafts are getting lighter and lighter: Lightweight structures help save fuel and lower CO2 emissions. "To ensure that police and marine emergency services can rely on their lifeboats, even in high seas, the lightweight components undergo comprehensive quality assurance before being put to actual use," affirms Joachim Montnacher, Head of Department for Testing Systems at the Fraunhofer Institute for Manufacturing Engineering and Automation IPA in Stuttgart. Together with Dr. Tina Wilhelm, Group Manager for Measurement and Testing Technology, and colleague Wolfgang Schmidt, the experts are hard at work on quality assurance systems for lightweight construction. At the Composites Europe trade show, the researchers will present a combination of two testing systems: shearography and thermography.

"Shearography is a laser optical procedure that allows measurement of material deformations in the triple-digit nanometer range. Thermography allows one to measure temperature differences on the surface of materials with accuracy of just a few Millikelvins. If an air pocket is enclosed on the adhesive side of a component, then the thermographic camera will measure different heat values than those of the properly seamed locations. With shearography, the material expands differently at the site where a defect occurs," is how Wilhelm describes the test principle. For both procedures, the material must be stimulated mechanically, thermally or electrically, using force, ultrasound or light. The experts measure twice: Once before and once after the stimulus. The measurement values clearly indicate where delaminations, i.e. defects in the bonded connection, have occurred with the materials during processing.

"Depending on the procedure, various physical effects are used for the testing. What's important is that you can reliably detect defects with the two technologies - and specifically both on the surface and in the interior of the component. Since it is necessary to apply a stimulus to the materials being tested in any case, the combination allows you to eliminate one processing step, while simultaneously improving quality control," Montnacher summarizes the functional process of measurement and the advantage of the combination. At the trade show, the IPA researchers will demonstrate the two testing technologies on a clutch disk.

In the laboratory, the researchers are not only currently working on the combination of both measurement principles. An essential focal point of the working group is to ascertain for which materials shearography is best suited in order to find hidden delaminations, and when it is better to utilize thermography. "There is still a considerable amount of research needed," says Wilhelm.

Source: Fraunhofer-Gesellschaft (news : web)

Explore further: Off-world manufacturing is a go with space printer

add to favorites email to friend print save as pdf

Related Stories

Reliable to the nanometer

Nov 10, 2005

Small fault – major impact. Disruptions to production are often caused by electronic faults. They arise because no reliable measurement and testing methods exist for the ever-smaller dimensions of microchip components. ...

Seal of quality for hygienic equipment

Sep 14, 2009

The processing and packaging of food is governed by very strict hygiene rules. Researchers are now testing production equipment for cleanroom suitability and are listing qualified products in an online database.

Smart aircraft wings and new lightweight construction materials

Mar 26, 2008

At the JEC Composites Show 2008 to be held in Paris from April 1 to 3, Fraunhofer researchers will be exhibiting an aircraft wing that immediately detects any material damage. Another showcased development is a novel fiber-composite ...

Polymer composite provides better fire protection than steel

Mar 27, 2006

The U.S. Navy needs lighter materials so ships will go further faster. One way to do that is to use new composite materials. But how will these materials respond to fire -- one of the most critical safety concerns on a ship? ...

Self-healing surfaces

Aug 03, 2009

The engineers' dream of self-healing surfaces has taken another step towards becoming reality -- researchers have produced a electroplated layer that contains tiny nanometer-sized capsules. If the layer is ...

Lego system for production facilities

Mar 11, 2008

Things that work on a small scale are not necessarily as successful on a large one. It takes a lot of patience and money to scale up analytical or therapeutic processes from the laboratory to industrial manufacture. ...

Recommended for you

Off-world manufacturing is a go with space printer

5 hours ago

On Friday, the BBC reported on a NASA email exchange with a space station which involved astronauts on the International Space Station using their 3-D printer to make a wrench from instructions sent up in ...

First drone in Nevada test program crashes in demo

22 hours ago

A drone testing program in Nevada is off to a bumpy start after the first unmanned aircraft authorized to fly without Federal Aviation Administration supervision crashed during a ceremony in Boulder City.

Fully automated: Thousands of blood samples every hour

Dec 19, 2014

Siemens is supplying automation technology for the longest and one of the most cutting-edge sample processing lines in any clinical laboratory. The line, or automation track, 200 meters long, in Marlborough, ...

Explainer: What is 4-D printing?

Dec 19, 2014

Additive manufacturing – or 3D printing – is 30 years old this year. Today, it's found not just in industry but in households, as the price of 3D printers has fallen below US$1,000. Knowing you can p ...

User comments : 0

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.