Optical fiber could boost power of superconducting quantum computers

Optical fiber could boost power of superconducting quantum computers
NIST physicists measured and controlled a superconducting qubit using light-conducting fiber (indicated by arrow) instead of metal electrical cables like the 14 shown here. Credit: Lecocq/NIST

The secret to building superconducting quantum computers with massive processing power may be an ordinary telecommunications technology—optical fiber.

Physicists at the National Institute of Standards and Technology (NIST) have measured and controlled a superconducting quantum bit () using light-conducting fiber instead of metal electrical wires, paving the way to packing a million qubits into a quantum computer rather than just a few thousand. The demonstration is described in the March 25 issue of Nature.

Superconducting circuits are a leading technology for making quantum computers because they are reliable and easily mass produced. But these circuits must operate at , and schemes for wiring them to electronics are complex and prone to overheating the qubits. A universal quantum computer, capable of solving any type of problem, is expected to need about 1 million qubits. Conventional cryostats—supercold dilution refrigerators—with metal wiring can only support thousands at the most.

Optical fiber, the backbone of telecommunications networks, has a glass or plastic core that can carry a high volume of light signals without conducting heat. But superconducting quantum computers use to store and process information. So the light needs to be converted precisely to microwaves.

To solve this problem, NIST researchers combined the fiber with a few other standard components that convert, convey and measure light at the level of single particles, or photons, which could then be easily converted into microwaves. The system worked as well as metal wiring and maintained the qubit's fragile quantum states.

"I think this advance will have high impact because it combines two totally different technologies, photonics and superconducting qubits, to solve a very important problem," NIST physicist John Teufel said. "Optical fiber can also carry far more data in a much smaller volume than conventional cable."

Normally, researchers generate microwave pulses at room temperature and then deliver them through coaxial metal cables to ¬¬cryogenically maintained superconducting qubits. The new NIST setup used an instead of metal to guide light signals to cryogenic photodetectors that converted signals back to microwaves and delivered them to the qubit. For experimental comparison purposes, microwaves could be routed to the qubit through either the photonic link or a regular coaxial line.

The "transmon" qubit used in the fiber experiment was a device known as a Josephson junction embedded in a three-dimensional reservoir or cavity. This junction consists of two superconducting metals separated by an insulator. Under certain conditions an electrical current can cross the junction and may oscillate back and forth. By applying a certain , researchers can drive the qubit between low-energy and (1 or 0 in digital computing). These states are based on the number of Cooper pairs—bound pairs of electrons with opposite properties—that have "tunneled" across the junction.

The NIST team conducted two types of experiments, using the photonic link to generate microwave pulses that either measured or controlled the quantum state of the qubit. The method is based on two relationships: The frequency at which microwaves naturally bounce back and forth in the cavity, called the , depends on the qubit state. And the frequency at which the qubit switches states depends on the number of photons in the cavity.

Researchers generally started the experiments with a microwave generator. To control the qubit's quantum state, devices called electro-optic modulators converted microwaves to higher optical frequencies. These light signals streamed through optical fiber from room temperature to 4K (minus 269 C or minus 452 F) down to 20 milliKelvin (thousandths of a Kelvin) where they landed in high-speed semiconductor photodetectors, which converted the light signals back to microwaves that were then sent to the quantum circuit.

In these experiments, researchers sent signals to the qubit at its natural resonance frequency, to put it into the desired quantum state. The qubit oscillated between its ground and excited states when there was adequate laser power.

To measure the qubit's state, researchers used an infrared laser to launch light at a specific power level through the modulators, fiber and photodetectors to measure the cavity's resonance frequency.

Researchers first started the qubit oscillating, with the laser power suppressed, and then used the photonic link to send a weak pulse to the cavity. The cavity frequency accurately indicated the qubit's state 98% of the time, the same accuracy as obtained using the regular coaxial line.

The researchers envision a quantum processor in which in which light in optical fibers transmits signals to and from the qubits, with each fiber having the capacity to carry thousands of signals to and from the qubit.


Explore further

Scientists take step towards quantum supremacy

More information: Control and readout of a superconducting qubit using a photonic link, Nature (2021). DOI: 10.1038/s41586-021-03268-x
Journal information: Nature

Citation: Optical fiber could boost power of superconducting quantum computers (2021, March 24) retrieved 18 April 2021 from https://phys.org/news/2021-03-optical-fiber-boost-power-superconducting.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.
4049 shares

Feedback to editors

User comments