Technique streamlines fabrication of 2-D circuits

March 5, 2019 by Rob Matheson, Massachusetts Institute of Technology
MIT researchers have developed a technique to grow 2-D materials directly onto patterned substrates (shown here) and then recycle the patterns for faster, simpler chip manufacturing. Credit: Massachusetts Institute of Technology

Exotic 2-D materials hold great promise for creating atom-thin circuits that could power flexible electronics, optoelectronics, and other next-generation devices. But fabricating complex 2-D circuits requires multiple time-consuming, expensive steps.

In a paper published in PNAS, researchers from MIT and elsewhere describe a technique that streamlines the , by growing a 2-D material directly onto a patterned and recycling the .

The researchers carefully grow a single layer of (MoS2), which is just three atoms thick, onto a growth substrate in a chosen . This approach differs from traditional techniques that grow and etch away a material iteratively, over multiple layers. Those processes take a while and increase the chances of causing surface defects that may hinder the performance of the material.

With the new method, using only water, the researchers can transfer the material from its growth substrate to its destination substrate so cleanly that the original patterned substrate can be reused as a "master-replica" type of mold—meaning a reusable template for manufacturing. In traditional fabrication, growth substrates get tossed after each material transfer, and the circuit must be patterned again on a new substrate to regrow more material.

"When we scale up and make more complex electronic devices, people need to integrate numerous 2-D into more layers and specific shapes. If we follow traditional methods, step by step, it will be very time consuming and inefficient," says the first author Yunfan Guo, a postdoc in the Department of Electrical Engineering and Computer Science (EECS) and the Research Laboratory of Electronics. "Our method shows the potential to make the whole fabrication process simpler, lower cost, and more efficient."

In their work, the researchers fabricated arbitrary patterns and a working transistor made from MoS2, which is one of the thinnest known semiconductors. In their study, the researchers recycled the same patterned substrate four times without seeing signs of wear.

Guo is joined on the paper by EECS professors Tomas Palacios and Jing Kong; Ju Li, an MIT professor of nuclear science and engineering and of materials science and engineering; Xi Ling of Boston University; Letian Dou and Enzheng Shi of Purdue University; seven other MIT graduate students, postdocs, and alumni; and two other co-authors from Cornell University and Purdue University.

Controlled growth

To design a pattern on a growth substrate, the researchers leveraged a technique that uses oxygen-based plasma to carve patterns into a substrate's surface. Some version of this technique has been used experimentally before to grow 2-D material patterns. But the —meaning the size of precise structures that can be fabricated—is relatively poor (100 microns), and the electrical performance has been much lower than materials grown using other methods.

To fix this, the researchers conducted in-depth studies into how MoS2 atoms arrange themselves on a substrate surface and how certain chemical precursors can help control the material's growth. In doing so, they were able to leverage the technique to grow a single layer of high-quality MoS2 within precise patterns.

The researchers used traditional photolithography masks on a silicon oxide substrate, where the desired pattern lies within regions unexposed to light. Those regions are subsequently exposed to the oxygen-based plasma. The plasma etches away about 1-2 nanometers of the substrate in the pattern.

This process also creates a higher surface energy and an enhanced affinity for water-loving ("hydrophilic") molecules in these plasma-treated regions. The researchers then use an organic salt, called PTAS, that acts as a growth promoter for MoS2. The salt is attracted to the newly created hydrophilic etched regions. In addition, the researchers used sulfur, an essential precursor for MoS2 growth, at a precise amount and temperature to regulate exactly how many of the material's atoms will form on the substrate.

When the researchers subsequently measured the MoS2 growth, they found it filled in about 0.7 nanometers of the etched pattern. That's equivalent to exactly one layer of MoS2.

Recycled patterns

Next, the researchers developed a method to recycle the patterned substrate. Traditionally, transferring 2-D materials from a growth substrate onto a destination substrate, such as a flexible surface, requires encasing the whole grown material in a polymer, chemically etching it, and separating it from its growth substrate. But this inevitably brings in contaminants to the material. When the material released, it also leaves behind residue, so the original substrates may not be reused.

Due to the weak interaction between MoS2 and the growth substrate, however, the researchers found they could detach the MoS2 cleanly from the original substrate by submerging it in water. This process, called "delamination," eliminates the need for using any supporting layer and produces a clean break with the material from the substrate.

"That's why we can recycle it," Guo says. "After it's transferred, because it is purely clean, our patterned substrate is recovered and we can use it for multiple growths."

The researchers' innovations introduce far fewer surface defects that limit performance, as measured in electron mobility—how fast electrons move through a semiconductor.

In their paper, the researchers fabricated a 2-D transistor, called a . Results indicate the electron mobility and "on-off ratio"—how efficiently a transistor flicks between the 1 and 0 computational states—are comparable with the reported values of traditionally grown high-quality, high-performance materials.

The field-effect transistor currently has a spatial resolution of about 2 microns, which is limited only by the laser the microfabrication instruments the researchers used. Next, the researchers hope to shrink the pattern size, and directly integrate complex circuits on 2-D materials using their fabrication technique.

Explore further: New way to move atomically thin semiconductors for use in flexible devices

More information: Yunfan Guo et al. Additive manufacturing of patterned 2D semiconductor through recyclable masked growth, Proceedings of the National Academy of Sciences (2019). DOI: 10.1073/pnas.1816197116

Related Stories

Engineers produce smallest 3-D transistor yet

December 10, 2018

Researchers from MIT and the University of Colorado have fabricated a 3-D transistor that's less than half the size of today's smallest commercial models. To do so, they developed a novel microfabrication technique that modifies ...

Nobarrier to applications for a remarkable 2-D material

June 25, 2018

Mass production of large, uniform sheets of single-layer molybdenum disulfide, MoS2, is difficult, which limits its commercial application. A*STAR researchers have modified an existing manufacturing technique to enable the ...

Recommended for you

Physicists discover new class of pentaquarks

March 26, 2019

Tomasz Skwarnicki, professor of physics in the College of Arts and Sciences at Syracuse University, has uncovered new information about a class of particles called pentaquarks. His findings could lead to a new understanding ...

Study finds people who feed birds impact conservation

March 26, 2019

People in many parts of the world feed birds in their backyards, often due to a desire to help wildlife or to connect with nature. In the United States alone, over 57 million households in the feed backyard birds, spending ...

Matter waves and quantum splinters

March 25, 2019

Physicists in the United States, Austria and Brazil have shown that shaking ultracold Bose-Einstein condensates (BECs) can cause them to either divide into uniform segments or shatter into unpredictable splinters, depending ...


Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.