Tiny robots get a grip on nanotubes

Aug 17, 2009

(PhysOrg.com) -- How do you handle the tiny components needed for constructing nanoscale devices? A European consortium has built two microrobotic demonstrators that can automatically pick up and install carbon nanotubes thousands of times thinner than a human hair.

Carbon nanotubes, rolled up sheets of carbon only a few tens of nanometres in diameter, could become an essential part of the nanotechnologist’s construction kit. But there is a problem: how can you handle objects which are so thin that they cannot be seen at all with a normal ?

“The handling and characterisation of these objects has become more and more important in materials science and nanotechnology,” says Volkmar Eichhorn of the University of Oldenburg and its associated institute, OFFIS. “They have a huge application potential in various products.”

One solution, developed by the EU-funded NanoHand project, is to use mobile microrobots equipped with delicate handling tools. NanoHand builds on the work of ROBOSEM, an earlier EU project that developed the basic technologies that are now being put into effect.

The robots, about two centimetres in size, work inside a scanning electron microscope where their activities can be followed by an observer. “The whole set-up is integrated into the of the microscope,” Eichhorn explains. “There is a glass plate where these mobile microrobots can walk around.”

Microgrippers

Each robot has a ‘microgripper’ that can make precise and delicate movements. It works on an electrothermal principle to open and close the jaws, much like a pair of .

The jaws open to about 2 micrometres and can pick up objects less than 100 nanometres in size. “[It is] really able to grip micro or even nano objects,” Eichhorn says. “We have handled objects down to tens of nanometres.”

At that scale, the intermolecular forces between objects are stronger than gravity. Once a nanotube has been picked up it will stick to the jaws of the gripper and cannot easily be dropped into position. The team have had to develop novel ‘pick-and-place’ techniques to get around this problem.

This video is not supported by your browser at this time.

One approach is to glue the tube in its final position using electron beam-induced deposition. Another is to use geometrical principles to ensure that the intermolecular forces pulling the tube towards its intended location are greater than those holding it in the jaws of the gripper.

“Worldwide, we are the first project that has really realised the automated microgripper-based pick-and-place experiments,” Eichhorn notes. “The new thing is the high accuracy and the small scale of the objects - in the range of tens or hundreds of nanometres - and the excellent control and software architecture being built around this whole set-up facilitating a high degree of automation.”

Better microscope

An early success of the project was to improve the performance of an atomic force microscope, a workhorse of nanotechnology.

The microscope ‘feels’ a surface by dragging a fine probe over it. Individual atoms can be sensed and a picture built up. But conventional probes have a pyramid-shaped tip which cannot follow the hills and valleys of deeply corrugated surfaces. The NanoHand team used their microrobots to automatically pick up a and attach it to the tip, so greatly improving the probe’s ability to sense deep valleys.

This achievement was made with the ‘NanoLab’ demonstrator, designed for use in experimental laboratory situations.

In parallel, the industrial partners have developed a more robust ‘NanoFab’ demonstrator, better suited to the needs of industry. They are exploring how the technology could be used for rapid prototyping of new designs for microchips. One idea is to use carbon nanotubes as ‘interconnects’, the fine wires that make the electrical connections to a chip. Because of their high electrical conductivity, carbon nanotubes dissipate less heat than copper and allow circuits to be packed more densely.

This application is of particular interest to STMicroelectronics, one of the project partners and a heavyweight maker of microchips. “They would like to have a nanorobotic system where they can do fast and rapid characterisation of these devices,” says Eichhorn. “Up to now, it was a manual, teleoperated characterisation which was very time consuming.”

Early exploitation

Many other industrial applications are possible, including novel devices that could not be constructed any other way. Applications in composite materials, displays and new kinds of transistors are all being talked about.

Other groups are working on methods of handling nanotubes, especially in the USA, Japan and China, but the NanoHand system of microrobots and microgrippers is proving effective and reliable. “It’s very promising for nanotechnology applications,” says Eichhorn.

From the start, the project has been run with commercialisation in mind and the first product is already on the market. Two of the industrial partners, Tescan and Klocke Nanotechnik, are collaborating to sell a equipped with a nanopositioning system based on NanoHand technology.

The Technical University of Denmark (DTU Nanotech) intends to set up a spin-off to market the microgrippers and the Ecoles Polytechniques Fédérale de Lausanne (EPFL) is seeking to further develop the microrobots to the point where they can be commercialised.

Provided by ICT Results

Explore further: Toward making lithium-sulfur batteries a commercial reality for a bigger energy punch

add to favorites email to friend print save as pdf

Related Stories

Two Robot Chefs Make Omelets

Dec 04, 2008

(PhysOrg.com) -- No "house of the future" is complete without a household robot to do the cooking and cleaning. Although today´s robots still have a ways to go before substituting for a real live-in maid, ...

A Perfect Female Companion: Project Aiko

Dec 12, 2008

(PhysOrg.com) -- Aiko is a humanoid robot with a built in Biometric Artificial Intelligence Neural System (Brain) designed by Le Trung in Canada. Aiko is slightly less than 5-feet high with 32.24-inch bust, ...

Embedded electronics -- cars get cooperative

Jul 01, 2009

(PhysOrg.com) -- European researchers have developed a groundbreaking middleware platform that could lead to thousands of new applications in a range of industries. Beginning with in-car electronics, the platform ...

Pervasive collaboration for modern business

Jan 12, 2009

(PhysOrg.com) -- Highly dispersed and mobile teams are the definition of modern business, but organising them is a hard problem. Now European researchers have developed a service bundle that could make virtual team organisation ...

Recommended for you

For electronics beyond silicon, a new contender emerges

Sep 16, 2014

Silicon has few serious competitors as the material of choice in the electronics industry. Yet transistors, the switchable valves that control the flow of electrons in a circuit, cannot simply keep shrinking ...

Making quantum dots glow brighter

Sep 16, 2014

Researchers from the University of Alabama in Huntsville and the University of Oklahoma have found a new way to control the properties of quantum dots, those tiny chunks of semiconductor material that glow ...

The future face of molecular electronics

Sep 16, 2014

The emerging field of molecular electronics could take our definition of portable to the next level, enabling the construction of tiny circuits from molecular components. In these highly efficient devices, ...

Study sheds new light on why batteries go bad

Sep 14, 2014

A comprehensive look at how tiny particles in a lithium ion battery electrode behave shows that rapid-charging the battery and using it to do high-power, rapidly draining work may not be as damaging as researchers ...

User comments : 1

Adjust slider to filter visible comments by rank

Display comments: newest first

antialias_physorg
not rated yet Aug 17, 2009
First project that did this? May I laugh? Check out the german BMBF project REMROB. We did stuff like this 5 years ago (including force feedback).

(BTW: Volkmar Eichhorn should know this - The University of Oldenburg and the AMIR group were one of the partners in the REMROB project)