Directivity to improve optical devices

November 9, 2018, AMOLF
Nanophotonic lens optimization and structure. (a) Progression of the evolutionary algorithm at four example generations, with cross-sections of the lens structure and the corresponding directivity, D, values shown. The full 3D structure of the final nanolens design is rendered in (b), with a scanning electron microscope image of the actual experimental lenses shown in (c). Credit: AMOLF

A team of researchers from the Dutch institute AMOLF, Western University (Canada), and the University of Texas (United States of America) recently demonstrated the use of algorithmic design to create a new type of nanophotonic structure. This is good news for researchers in optical quantum computing and photovoltaics, because the structure greatly improves the directivity of nanoscale emitters (in light emitting diodes, or single photon sources) and absorbers (in solar cells or photodetectors). The researchers published their findings in Nature Communications on November 9th, 2018.

Directivity describes the ratio of light emission in one particular direction to the total over all other directions. It is often useful for emitters to have high directivity so that all of the photons created by a nanoscale source can be collected elsewhere. This is particularly valuable in applications in which the collection from single photon emitters proves challenging.

Furthermore, improving directivity is beneficial for nanoscale photovoltaic devices as well; coupling the active absorber material in exclusively with the sun can improve the photovoltage significantly. This can be understood through an analogy—when heating a material with sunlight, it will get warmer when it is only exchanging energy with the sun, and not with the relatively colder surrounding environment.

Directivity at the nanoscale

While directivity is a highly advantageous property for emitters and absorbers, increasing it for nanoscale devices can be challenging. At such small length scales, light behaves both as a particle and a wave, complicating the design of structures with sub-wavelength features to the point that intuition of the performance of an optical element is extremely limited. Designing structures using algorithms addresses this, allowing full-wave optical simulations to fully dictate the geometry of the nanophotonic object. The research team used an evolutionary algorithm, to create multiple generations of structures with increasing performance. This resulted in directivity values exceeding those of classical structures such as spherical lenses by more than a factor of three.

To demonstrate the feasibility of these structures, a proof of concept device was experimentally fabricated. This device involved printing a nanolens on top of a gallium arsenide nanowire using a femtosecond pulsed laser technique. Such GaAs nanowires were used for their relevance in photovoltaic devices, while also providing a convenient test system due to their high quantum efficiency (number of photons out per photon in).

While the nanolenses dramatically improved the directivity of the nanowire emitters, the observed performance was still less than the computational design had predicted. However, by including a small offset between the center of emission and center of the lens, new simulations were able to reproduce the observed behavior. This offset likely occurred in the experimental samples, as the nanowires emit primary from a small region near one of their ends (corresponding the position of the internal diode junction in the wire). The difficulty to align to this emitting location proved to be the single greatest limitation in the observed performance, followed by the fact that this emission was still from a finite region (not a single point, as assumed in the design simulations). This indicates that moving to more confined or absorber structures could easily address both of these sources of decreased performance, and offer even more directive behavior without needing to change the lens or fabrication techniques.

Explore further: High-speed and on-silicon-chip graphene blackbody emitters

More information: Eric Johlin, Sander A. Mann, Sachin Kasture, A. Femius Koenderink & Erik C. Garnett, Broadband highly directive 3D nanophotonic lenses, Nature Communications (2018) DOI: 10.1038/s41467-018-07104-1

Related Stories

High-speed and on-silicon-chip graphene blackbody emitters

April 4, 2018

High-speed light emitters integrated on silicon chips can enable novel architectures for silicon-based optoelectronics. However, compound-semiconductor-based light emitters face major challenges for their integration with ...

Recommended for you

Solving mazes with single-molecule DNA navigators

November 16, 2018

The field of intelligent nanorobotics is based on the great promise of molecular devices with information processing capabilities. In a new study that supports the trend of DNA-based information carriers, scientists have ...

A way to make batteries almost any shape desired

November 16, 2018

A team of researchers from Korea Advanced Institute of Science and Technology, Harvard University and Korea Research Institute of Chemical Technology has developed a way to make batteries in almost any shape that can be imagined. ...

Graphene flickers at 400Hz in 2500ppi displays

November 16, 2018

With virtual reality (VR) sizzling in every electronic fair, there is a need for displays with higher resolution, frame rates and power efficiency. Now, a joint collaboration of researchers from SCALE Nanotech, Graphenea ...

'Smart skin' simplifies spotting strain in structures

November 15, 2018

Thanks to one peculiar characteristic of carbon nanotubes, engineers will soon be able to measure the accumulated strain in an airplane, a bridge or a pipeline – or just about anything – over the entire surface or down ...

0 comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.