Storing a Lightning Bolt in Glass for Portable Power

May 05, 2009
Glass film.

(PhysOrg.com) -- Materials researchers at Penn State University have reported the highest known breakdown strength for a bulk glass ever measured. Breakdown strength, along with dielectric constant, determines how much energy can be stored in an insulating material before it fails and begins to conduct electricity.

A bulk with high breakdown strength and high dielectric constant would make an ideal candidate for the next generation of high energy density storage capacitors to power more efficient electric vehicles, as well as other portable and pulsed power applications.

The highest dielectric breakdown strengths for bulk glasses are typically in the 4-9MV/cm range. The breakdown strength for the tested samples were in the 12MV/cm range, which in conjunction with a relatively high permittivity, resulted in energy densities of 35 J/cm3, as compared to a maximum energy density of 10 J/cm3 for polypropylene, the most common dielectric for pulsed power applications.

“For a bulk glass, this is extraordinary,” says Nick Smith, a Ph.D. candidate in materials science and engineering at Penn State, who is lead author on the report and performed the testing. Smith used samples of 50 micron-thick commercial glass, which he etched for testing with hydrofluoric acid until the samples were only 10-20 microns thick. The resulting glass was so thin it could be flexed like a piece of plastic film, yet so delicate it could easily disintegrate if mishandled. The thinner the glass, the more electric field can be applied before failure.

The etched glass was placed in a polymer fluid for testing and up to 30,000 volts were applied. When the breakdown point was reached, electricity began to flow through the glass suddenly, with a flash and a bang that resembles a lightning bolt conducting through air. The polymer fluid was used to contain the lightning. In each case, failure occurred within 40 to 80 seconds.

The bulk glass tested is an alkali-free barium boroaluminosilicate glass produced in large quantities for flat panel displays and microelectronics packaging. Its high energy storage capability is attributed to the highly polarizable barium atoms, which contribute to the enhanced permittivity, and the alkali-free composition, which inhibits energy loss. Also a factor is the nearly defect-free quality of the glass. The specific process used to manufacture this glass yields a more flaw-free material, especially at the surface, which further enhances resistance to breakdown.

Sheets of 30-micron-thick glass, which are expected to be available commercially in the near future, are likely to have even higher breakdown strength than the etched glass due to an even more uniform flaw-free surface. “This opens a potentially new market for glass,” says Smith. “We are always looking for new functionalities in glass. Ideally, manufacturing will get to a point where they can make any size sheet they need for any size capacitor.”

Contributing author Michael Lanagan points out that engineering challenges remain as they scale up from the small size glass capacitors tested to those ready for commercial production. “We’ll lose some of the energy density as we increase in volume,“ he says, “but we should still end up with some remarkable capacitance.”

A paper reporting their results, titled “Glass as a High Energy Density Dielectric Material,” is currently available online and in the June 2009 edition of Materials Letters. In addition to Smith, the authors are graduate student Badri Rangarajan, engineering science and mechanics, Michael T. Lanagan, associate professor of engineering science and mechanics, and Carlo G. Pantano, distinguished professor of materials science and engineering.

Provided by Pennsylvania State University

Explore further: The mysterious 'action at a distance' between liquid containers

add to favorites email to friend print save as pdf

Related Stories

Polymer electric storage, flexible and adaptable

Aug 20, 2008

(PhysOrg.com) -- The proliferation of solar, wind and even tidal electric generation and the rapid emergence of hybrid electric automobiles demands flexible and reliable methods of high-capacity electrical storage. Now a ...

Unique Material May Allow Capacitors to Store More Energy

Jul 20, 2007

Imagine an electric car with the same acceleration capability as a gas-powered sports car, or ultrafast rechargeable “batteries” that can be recharged a thousand times more than existing conventional batteries. According ...

High-performance energy storage

Jul 03, 2007

North Carolina State University physicists have recently deduced a way to improve high-energy-density capacitors so that they can store up to seven times as much energy per unit volume than the common capacitor.

Recommended for you

User comments : 8

Adjust slider to filter visible comments by rank

Display comments: newest first

Alizee
May 05, 2009
This comment has been removed by a moderator.
TJ_alberta
not rated yet May 05, 2009
thanks Alizee. Excellent sites. A whole world of physics in a block of plastic.
Bob_Kob
not rated yet May 05, 2009
I can imagine, in the future we will all carry around lightning in a crystal for power.
KBK
not rated yet May 06, 2009
I can imagine, in the future we will all carry around lightning in a crystal for power.


Just like the Ole Days. Here we go again.....
Ruggy
not rated yet May 07, 2009
Fantastic discovery!

I am curious how long these thin sheets of glass will last in an ultracapacitor, given that glass is technically not a solid but a liquid, and as such it can flow very slowly. Of course normally this is so slow that we can disregard it entirely. But could this be a concern down at the micron scale?
Alexa
1 / 5 (1) May 07, 2009
this be a concern down at the micron scale?
Nope, the main trick is, every sheet of light contains tiny invisible surface cracks, which are removed by action of hydrofluoric acid. This makes the sheet of light so bendable, by the way - this is a well known phenomena. But the same effect can be achieved by covering of glass surface by thin layer of varnish.

Another effect of acid may be in removal of residual traces of alkali metal ions, which are the main source of ion conductivity of glass at elevated temperature. Common sheet of glass contains a more conductive surface layer rich of alkali metal ions from production and the hydrofluoric acid etching removes this surface layer.


After all, this is why the barium glass was used: barium ions are bivalent and as such they're incorporated into silicate structure more firmly then univalent alkali metal ions - so they cannot move so easily in strong electrostatic field.
Slotin
1 / 5 (1) May 07, 2009
Errata: "sheet of light" = sheet of glass, indeed...
thubten
not rated yet Jun 10, 2009
Who will produce a prototype product first Penn State or EEstor?
HeyZeuss
not rated yet Sep 05, 2009
33J/cubic cm seems pathetic. thats only 1kw for 15seconds from 1kg....

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.