Nanotechnology helps scientists make bendy sensors for hydrogen vehicles

Jul 31, 2007

In recent years, Americans have been intrigued by the promise of hydrogen-powered vehicles. But experts have judged that several technology problems must be resolved before they are more than a novelty.

Recently, scientists at the U.S. Department of Energy's Argonne National Laboratory have used their insights into nanomaterials to create bendy hydrogen sensors, which are at the heart of hydrogen fuel cells used in hydrogen vehicles.

In comparison to previously designed hydrogen sensors, which are rigid and use expensive, pure palladium, the new sensors are bendy and use single-walled carbon nanotubes (SWNTs) to improve efficiency and reduce cost. The development of these hydrogen sensors will help to ensure economical, environmental and societal safety, as the nation is realizing the potential for a more hydrogen-based economy.

Yugang Sun and H. Hau Wang, researchers in Argonne's Center for Nanoscale Materials and Materials Science Division, respectively, fabricated the new sensing devices using a two-step process separated by high and low temperatures. First, at around 900 degrees C, researchers grow SWNTs on a silicon substrate using chemical vapor deposition. Then, researchers transfer the SWNTs onto a plastic substrate at temperatures lower than 150 degrees C using a technique called dry transfer printing.

This precise process is what allows the film of nanotubes to form on the plastic, after which the palladium nanoparticles can be deposited on the SWNTs to make the sensors. The palladium nanoparticles play an important role in increasing the interaction between hydrogen and the SWNTs to enhance the change of resistance of the device when it is exposed to hydrogen molecules.

According to Sun, these sensors exhibit excellent sensing performance in terms of high sensitivity, fast response time and quick recovery, and the use of plastic sheets reduces their overall weight and increases their mechanical flexibility and shock resistance. The sensors are also able to be wrapped around curved surfaces, and this proves useful in many applications, notably in vehicles, aircraft and portable electronics.

“The leakage of hydrogen caused by tiny pinholes in the pipe of a space shuttle, for example, could not be easily detected by individual rigid detectors because the locations of pinholes are not predetermined,” said Sun. “However, laminating a dense array of flexible sensors on the surfaces of the pipe can detect any hydrogen leakage prior to diffusion to alert control units to take action.”

Flexible hydrogen sensors show a change of 75 percent in their resistance when exposed to hydrogen at a concentration of 0.05 percent in air. The devices can detect the presence of 1 percent hydrogen at room temperature in 3 seconds. Even after bending—with a bending radius of approximately 7.5 mm—and relaxing 2,000 times, the devices still perform with as much effectiveness.

Source: Argonne National Laboratory

Explore further: Technique for quantification of erythrocyte zinc protoporphyrin IX and protoporphyrin IX

add to favorites email to friend print save as pdf

Related Stories

Researchers uncover secrets of internal cell fine-tuning

39 minutes ago

New research from scientists at the University of Kent has shown for the first time how the structures inside cells are regulated – a breakthrough that could have a major impact on cancer therapy development.

Local education politics 'far from dead'

39 minutes ago

Teach for America, known for recruiting teachers, is also setting its sights on capturing school board seats across the nation. Surprisingly, however, political candidates from the program aren't just pushing ...

First grade reading suffers in segregated schools

49 minutes ago

A groundbreaking study from the Frank Porter Graham Child Development Institute (FPG) has found that African-American students in first grade experience smaller gains in reading when they attend segregated schools—but the ...

Printing the metals of the future

49 minutes ago

3-D printers can create all kinds of things, from eyeglasses to implantable medical devices, straight from a computer model and without the need for molds. But for making spacecraft, engineers sometimes need ...

Getting a jump on plant-fungal interactions

59 minutes ago

Fungal plant pathogens may need more flexible genomes in order to fully benefit from associating with their hosts. Transposable elements are commonly found with genes involved in symbioses.

Recommended for you

Light pulses control graphene's electrical behavior

16 hours ago

Graphene, an ultrathin form of carbon with exceptional electrical, optical, and mechanical properties, has become a focus of research on a variety of potential uses. Now researchers at MIT have found a way to control how ...

User comments : 0