Now, self-healing materials can mimic human skin, healing again and again

Jun 11, 2007

The next generation of self-healing materials, invented by researchers at the University of Illinois, mimics human skin by healing itself time after time. The new materials rely upon embedded, three-dimensional microvascular networks that emulate biological circulatory systems.

“In the same manner that a cut in the skin triggers blood flow to promote healing, a crack in these new materials will trigger the flow of healing agent to repair the damage,” said Nancy Sottos, a Willett Professor of materials science and engineering, and the corresponding author of a paper accepted for publication in the journal Nature Materials, and posted on its Web site.

“The vascular nature of this new supply system means minor damage to the same location can be healed repeatedly,” said Sottos, who also is a researcher at the university’s Beckman Institute.

In the researchers’ original approach, self-healing materials consisted of a microencapsulated healing agent and a catalyst distributed throughout a composite matrix. When the material cracked, microcapsules would rupture and release healing agent. The healing agent then reacted with the embedded catalyst to repair the damage.

“With repeated damage in the same location, however, the supply of healing agent would become exhausted,” said Scott White, a Willett Professor of aerospace engineering and a researcher at the Beckman Institute. “In our new circulation-based approach, there is a continuous supply of healing agent, so the material could heal itself indefinitely.”

To create their self-healing materials, the researchers begin by building a scaffold using a robotic deposition process called direct-write assembly. The process employs a concentrated polymeric ink, dispensed as a continuous filament, to fabricate a three-dimensional structure, layer by layer.

Once the scaffold has been produced, it is surrounded with an epoxy resin. After curing, the resin is heated and the ink – which liquefies – is extracted, leaving behind a substrate with a network of interlocking microchannels.

In the final steps, the researchers deposit a brittle epoxy coating on top of the substrate, and fill the network with a liquid healing agent.

In the researchers’ tests, the coating and substrate are bent until a crack forms in the coating. The crack propagates through the coating until it encounters one of the fluid-filled “capillaries” at the interface of the coating and substrate. Healing agent moves from the capillary into the crack, where it interacts with catalyst particles. If the crack reopens under additional stress, the healing cycle is repeated.

“Ultimately, the ability to achieve further healing events is controlled by the availability of active catalyst,” said Kathleen S. Toohey, a U. of I. graduate student and lead author of the paper. “While we can pump more healing agent into the network, ‘scar tissue’ builds up in the coating and prevents the healing agent from reaching the catalyst.”

In the current system, the healing process stops after seven healing cycles. This limitation might be overcome by implementing a new microvascular design based on dual networks, the researchers suggest. The improved design would allow new healing chemistries – such as two-part epoxies – to be exploited, which could ultimately lead to unlimited healing capability.

“Currently, the material can heal cracks in the epoxy coating – analogous to small cuts in skin,” Sottos said. “The next step is to extend the design to where the network can heal ‘lacerations’ that extend into the material’s substrate.”

Source: University of Illinois at Urbana-Champaign

Explore further: Spin-based electronics: New material successfully tested

add to favorites email to friend print save as pdf

Related Stories

Skin with high rust protection factor

Jun 04, 2014

In industrialized countries, corrosion guzzles up to 4 percent of economic performance annually. Substances that protect metals effectively from its ravages are often damaging to the environment or have other ...

Polymer coatings based on molecular structures

Dec 18, 2013

A novel method developed by researchers from Karlsruhe Institute of Technology (KIT) and Jacobs University Bremen enables manufacturing of polymer layers with tailor-made properties and multiple functions: ...

Recommended for you

MRI for a quantum simulation

1 hour ago

Magnetic resonance imaging (MRI), which is the medical application of nuclear magnetic resonance spectroscopy, is a powerful diagnostic tool. MRI works by resonantly exciting hydrogen atoms and measuring ...

50-foot-wide Muon g-2 electromagnet installed at Fermilab

1 hour ago

One year ago, the 50-foot-wide Muon g-2 electromagnet arrived at the U.S. Department of Energy's Fermi National Accelerator Laboratory in Illinois after traveling 3,200 miles over land and sea from Long Island, ...

User comments : 0