Which factors control the height of mountains?

Which factors control the height of mountains?
The height of the Andes, like the height of other mountain ranges on Earth, is determined by tectonic forces. Credit: NASA; Astronaut photograph ISS059-E-517

Which forces and mechanisms determine the height of mountains? A group of researchers from Münster and Potsdam has now found a surprising answer: It is not erosion and weathering of rocks that determine the upper limit of mountain massifs, but rather an equilibrium of forces in the Earth's crust. This is a fundamentally new and important finding for the earth sciences. The researchers report on it in the scientific journal Nature.

The highest ranges on Earth—such as the Himalayas or the Andes—arise along convergent plate boundaries. At such plate boundaries, two move toward each other, and one of the plates is forced beneath the other into the Earth's mantle. During this process of subduction, strong earthquakes repeatedly occur on the plate interface, and over millions of years, mountain ranges are built at the edges of the continents.

Whether the height of mountain ranges is mainly determined by tectonic processes in the Earth's interior or by erosional processes sculpturing the Earth's surface has long been debated in geosciences.

A new study led by Armin Dielforder of GFZ German Research Centre for Geoscience now shows that erosion by rivers and glaciers has no significant influence on the height of mountain ranges. Together with scientists from the GFZ and the University of Münster (Germany), he resolved the longstanding debate by analyzing the strength of various plate boundaries and calculating the forces acting along the plate interfaces.

The researchers arrived at this surprising result by calculating the forces along different plate boundaries on the Earth. They used data that provide information about the strength of plate boundaries. These data are derived, for example, from heat flow measurements in the subsurface. The heat flow at convergent plate boundaries is in turn influenced by the frictional energy at the interfaces of the continental plates.

Which factors control the height of mountains?
The diagram compares the average height of mountain ranges with the shear force (DFs) that acts along tectonic plate boundaries. It can be seen that the mountain height increases linearly with this force. This finding indicates that the height of mountain ranges is mainly tectonically controlled and that global differences in mountain height result from differences in the shear force. Credit: Dielforder et al. 2020, Nature: DOI 10.1038/s41586-020-2340-7

One can imagine the formation of mountains using a tablecloth. If you place both hands under the cloth on the table top and push it, the cloth folds, and at the same time, it slides a little over the back of your hands. The emerging folds would correspond, for instance, to the Andes, the sliding over the back of the hands to the friction in the underground. Depending on the characteristics of the rock, tensions also build up in the deep underground which are discharged in severe earthquakes, especially in subduction zones.

The researchers collected worldwide data from the literature on friction in the subsurface of mountain ranges of different heights (Himalayas, Andes, Sumatra, Japan) and calculated the resulting stress and thus the forces that lead to the uplift of the respective mountains. In this way, they showed that in active mountains, the on the boundary and the forces resulting from the weight and height of the mountains are in balance.

Such a balance of forces exists in all the mountain ranges studied, although they are located in different climatic zones with widely varying erosion rates. This result shows that are able to react to processes on the Earth's surface and to grow with rapid erosion in such a way that the balance of forces and the height of the mountain range are maintained. This fundamentally new finding opens up numerous opportunities to study the long-term development and growth of mountains in greater detail.


Explore further

The origin of the Andes unravelled

More information: Megathrust shear force controls mountain height at convergent plate margins, Nature (2020). DOI: 10.1038/s41586-020-2340-7 , www.nature.com/articles/s41586-020-2340-7
Journal information: Nature

Citation: Which factors control the height of mountains? (2020, June 11) retrieved 6 August 2020 from https://phys.org/news/2020-06-factors-height-mountains.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.
118 shares

Feedback to editors

User comments