Expanding polymer enables self-folding printable structures without heating or immersion in water

September 13, 2017 by Larry Hardesty
A new method produces a printable structure that begins to fold itself up as soon as it’s peeled off the printing platform. Credit: Massachusetts Institute of Technology

As 3-D printing has become a mainstream technology, industry and academic researchers have been investigating printable structures that will fold themselves into useful three-dimensional shapes when heated or immersed in water.

In a paper appearing in the American Chemical Society's journal Applied Materials and Interfaces, researchers from MIT's Computer Science and Artificial Intelligence Laboratory (CSAIL) and colleagues report something new: a printable structure that begins to fold itself up as soon as it's peeled off the printing platform.

One of the big advantages of devices that self-fold without any outside stimulus, the researchers say, is that they can involve a wider range of and more delicate structures.

"If you want to add printed electronics, you're generally going to be using some organic materials, because a majority of printed electronics rely on them," says Subramanian Sundaram, an MIT graduate student in electrical engineering and computer science and first author on the paper. "These materials are often very, very sensitive to moisture and temperature. So if you have these electronics and parts, and you want to initiate folds in them, you wouldn't want to dunk them in water or heat them, because then your electronics are going to degrade."

To illustrate this idea, the researchers built a prototype self-folding printable device that includes electrical leads and a polymer "pixel" that changes from transparent to opaque when a voltage is applied to it. The device, which is a variation on the "printable goldbug" that Sundaram and his colleagues announced earlier this year, starts out looking something like the letter "H." But each of the legs of the H folds itself in two different directions, producing a tabletop shape.

Expanding polymer enables self-folding printable structures without heating or immersion in water
This clip shows an example of an accelerated fold. Credit: om Buehler/CSAIL

The researchers also built several different versions of the same basic hinge design, which show that they can control the precise angle at which a joint folds. In tests, they forcibly straightened the hinges by attaching them to a weight, but when the weight was removed, the hinges resumed their original folds.

In the short term, the technique could enable the custom manufacture of sensors, displays, or antennas whose functionality depends on their three-dimensional shape. Longer term, the researchers envision the possibility of printable robots.

Sundaram is joined on the paper by his advisor, Wojciech Matusik, an associate professor of and computer science (EECS) at MIT; Marc Baldo, also an associate professor of EECS, who specializes in organic electronics; David Kim, a technical assistant in Matusik's Computational Fabrication Group; and Ryan Hayward, a professor of polymer science and engineering at the University of Massachusetts at Amherst.

Stress relief

The key to the researchers' design is a new printer-ink material that expands after it solidifies, which is unusual. Most printer-ink materials contract slightly as they solidify, a technical limitation that designers frequently have to work around.

Credit: Massachusetts Institute of Technology

Printed devices are built up in layers, and in their prototypes the MIT researchers deposit their expanding material at precise locations in either the top or bottom few layers. The bottom layer adheres slightly to the printer platform, and that adhesion is enough to hold the device flat as the layers are built up. But as soon as the finished device is peeled off the platform, the joints made from the new material begin to expand, bending the device in the opposite direction.

Like many technological breakthroughs, the CSAIL researchers' discovery of the material was an accident. Most of the printer materials used by Matusik's Computational Fabrication Group are combinations of polymers, long molecules that consist of chainlike repetitions of single molecular components, or monomers. Mixing these components is one method for creating printer inks with specific physical properties.

While trying to develop an ink that yielded more flexible printed components, the CSAIL researchers inadvertently hit upon one that expanded slightly after it hardened. They immediately recognized the potential utility of expanding polymers and began experimenting with modifications of the mixture, until they arrived at a recipe that let them build joints that would expand enough to fold a printed device in half.

Whys and wherefores

Hayward's contribution to the paper was to help the MIT team explain the material's expansion. The ink that produces the most forceful expansion includes several long molecular chains and one much shorter chain, made up of the monomer isooctyl acrylate. When a layer of the ink is exposed to ultraviolet light—or "cured," a process commonly used in 3-D printing to harden materials deposited as liquids—the long chains connect to each other, producing a rigid thicket of tangled molecules.

Plants like the Jewelweed (Impatiens capensis; or commonly, spotted touch-me-not) use stress ingeniously for the ballistic dispersal of their seeds. The plant stores energy in its seed pods in the form of inbuilt stresses by controlling tissue hydration. When gently touched, these pods explode and curl up to launch their seeds. Using a similar concept, S. Sundaram and coworkers demonstrate the use of 3D-printing to fabricate flat electronic composites with residual stress in specific regions. Credit: Massachusetts Institute of Technology

When another layer of the material is deposited on top of the first, the small chains of isooctyl acrylate in the top, liquid layer sink down into the lower, more rigid layer. There, they interact with the longer chains to exert an expansive force, which the adhesion to the printing platform temporarily resists.

The hope that a better theoretical understanding of the reason for the material's expansion will enable them to design material tailored to specific applications—including materials that resist the 1–3 percent contraction typical of many printed polymers after curing.

"This work is exciting because it provides a way to create functional electronics on 3-D objects," says Michael Dickey, a professor of chemical engineering at North Carolina State University. "Typically, electronic processing is done in a planar, 2-D fashion and thus needs a flat surface. The work here provides a route to create electronics using more conventional planar techniques on a 2-D surface and then transform them into a 3-D shape, while retaining the function of the electronics. The transformation happens by a clever trick to build stress into the materials during printing."

Explore further: New 3-D-printed device mimics the goldbug beetle, which changes color when prodded

More information: Subramanian Sundaram et al. 3D-Printed Self-Folding Electronics, ACS Applied Materials & Interfaces (2017). DOI: 10.1021/acsami.7b10443

Related Stories

Low-cost wearables manufactured by hybrid 3-D printing

September 7, 2017

Human skin must flex and stretch to accommodate the body's every move. Anything worn tight on the body must also be able to flex around muscles and joints, which helps explain why synthetic fabrics like spandex are popular ...

Strengthening 3-D printed parts for real-world use

July 20, 2017

From aerospace and defense to digital dentistry and medical devices, 3-D printed parts are used in a variety of industries. Currently, 3-D printed parts are very fragile and only used in the prototyping phase of materials ...

Making new functional polymers for 3-D printers

October 19, 2016

Chemical engineers at the University of Melbourne have found a way to 3-D print smart polymers (or plastics) that can perform a function, in a way that is cheaper, cleaner and more accessible than ever before.

Recommended for you

Scientific advances can make it easier to recycle plastics

November 17, 2017

Most of the 150 million tons of plastics produced around the world every year end up in landfills, the oceans and elsewhere. Less than 9 percent of plastics are recycled in the United States, rising to about 30 percent in ...

The spliceosome—now available in high definition

November 17, 2017

UCLA researchers have solved the high-resolution structure of a massive cellular machine, the spliceosome, filling the last major gap in our understanding of the RNA splicing process that was previously unclear.

Ionic 'solar cell' could provide on-demand water desalination

November 15, 2017

Modern solar cells, which use energy from light to generate electrons and holes that are then transported out of semiconducting materials and into external circuits for human use, have existed in one form or another for over ...

0 comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.