Experiments demonstrate how memristors work

Experiments demonstrate how memristors work
This animation shows how millions of high-voltage switching cycles can cause memristors to fail. The high-voltage switching eventually creates regions that are permanently rich (blue pits) or deficient (red peaks) in oxygen and cannot be switched back. Switching at lower voltages that would be suitable for commercial devices did not show this performance degradation. These observations allowed the researchers to develop materials processing and operating conditions that improved the memristors’ endurance by nearly a thousand times. Credit: Suhas Kumar

In experiments at two Department of Energy national labs – SLAC National Accelerator Laboratory and Lawrence Berkeley National Laboratory – scientists at Hewlett Packard Enterprise (HPE) have experimentally confirmed critical aspects of how a new type of microelectronic device, the memristor, works at an atomic scale.

This result is an important step in designing these solid-state devices for use in future computer memories that operate much faster, last longer and use less energy than today's . The results were published in February in Advanced Materials.

"We need information like this to be able to design memristors that will succeed commercially," said Suhas Kumar, an HPE scientist and first author on the group's technical paper.

The memristor was proposed theoretically in 1971 as the fourth basic electrical device element alongside the resistor, capacitor and inductor. At its heart is a tiny piece of a transition metal oxide sandwiched between two electrodes. Applying a positive or negative voltage pulse dramatically increases or decreases the memristor's electrical resistance. This behavior makes it suitable for use as a "non-volatile" computer memory that, like flash memory, can retain its state without being refreshed with additional power.

Over the past decade, an HPE group led by senior fellow R. Stanley Williams has explored memristor designs, materials and behavior in detail. Since 2009 they have used intense synchrotron X-rays to reveal the movements of atoms in memristors during switching. Despite advances in understanding the nature of this switching, critical details that would be important in designing commercially successful circuits remained controversial. For example, the forces that move the atoms, resulting in dramatic resistance changes during switching, remain under debate.

In recent years, the group examined memristors made with oxides of titanium, tantalum and vanadium. Initial experiments revealed that switching in the tantalum oxide devices could be controlled most easily, so it was chosen for further exploration at two DOE Office of Science User Facilities – SLAC's Stanford Synchrotron Radiation Lightsource (SSRL) and Berkeley Lab's Advanced Light Source (ALS).

At ALS, the HPE researchers mapped the positions of before and after switching. For this, they used a scanning transmission X-ray microscope and an apparatus they built to precisely control the position of their sample and the timing and intensity of the 500-electronvolt ALS X-rays, which were tuned to see oxygen.

Experiments demonstrate how memristors work
X-ray imaging of memristors showed that switching their resistance state drives oxygen atoms outward from a conducting path (red peak) into surrounding regions (circular blue trench) about 200 nanometers away. In the background is a photo of a silica wafer on which dozens of test memristors have been created. Four square electrode pads and thin wires connected to each memristor allow researchers to switch its state and measure the resistance changes. Credit: Suhas Kumar

The experiments revealed that even weak voltage pulses create a thin conductive path through the memristor. During the pulse the path heats up, which creates a force that pushes oxygen atoms away from the path, making it even more conductive. Reversing the voltage pulse resets the memristor by sucking some of oxygen atoms back into the conducting path, thereby increasing the device's resistance. The memristor's resistance changes between 10-fold and 1 million-fold, depending on operating parameters like the voltage-pulse amplitude. This resistance change is dramatic enough to exploit commercially.

To be sure of their conclusion, the researchers also needed to understand if the tantalum atoms were moving along with the oxygen during switching. Imaging tantalum required higher-energy, 10,000-electronvolt X-rays, which they obtained at SSRL's Beam Line 6-2. In a single session there, they determined that the tantalum remained stationary.

"That sealed the deal, convincing us that our hypothesis was correct," said HPE scientist Catherine Graves, who had worked at SSRL as a Stanford graduate student. She added that discussions with SLAC experts were critical in guiding the HPE team toward the X-ray techniques that would allow them to see the tantalum accurately.

Kumar said the most promising aspect of the tantalum oxide results was that the scientists saw no degradation in switching over more than a billion voltage pulses of a magnitude suitable for commercial use. He added that this knowledge helped his group build memristors that lasted nearly a billion switching cycles, about a thousand-fold improvement.

"This is much longer endurance than is possible with today's flash memory devices," Kumar said. "In addition, we also used much higher voltage pulses to accelerate and observe memristor failures, which is also important in understanding how these devices work. Failures occurred when oxygen atoms were forced so far away that they did not return to their initial positions."

Beyond memory chips, Kumar says memristors' rapid switching speed and small size could make them suitable for use in logic circuits. Additional memristor characteristics may also be beneficial in the emerging class of brain-inspired neuromorphic computing circuits.

"Transistors are big and bulky compared to memristors," he said. "Memristors are also much better suited for creating the neuron-like voltage spikes that characterize neuromorphic circuits."

More information: Suhas Kumar et al. Direct Observation of Localized Radial Oxygen Migration in Functioning Tantalum Oxide Memristors, Advanced Materials (2016). DOI: 10.1002/adma.201505435

Suhas Kumar et al. In-operando synchronous time-multiplexed O K-edge x-ray absorption spectromicroscopy of functioning tantalum oxide memristors, Journal of Applied Physics (2015). DOI: 10.1063/1.4926477

Citation: Experiments demonstrate how memristors work (2016, June 15) retrieved 28 March 2024 from https://phys.org/news/2016-06-memristors.html
This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

Explore further

Making a new generation of memristors for digital memory and computation

32 shares

Feedback to editors