Engineers create 'superomniphobic' texture capable of repelling all liquids

November 27, 2014 by Matthew Chin, University of California, Los Angeles

Water beading on hydrophobic material
(Phys.org) —A pair of researchers from the UCLA Henry Samueli School of Engineering and Applied Science has created the first surface texture that can repel all liquids, no matter what material the surface is made of.

Because its design relies only on the of the texture, the texture could have industrial or biomedical applications. For example, the could slow corrosion and extend the life of parts in chemical and power plants, solar cells or cookware.

Water will bead up on a nonstick cooking pan because it is coated with a hydrophobic material that repels water thanks to its chemical composition. If the hydrophobic material also is rough at the microscopic scale, it can trap air at its surface, causing the water to bead up and roll around effortlessly. Scientists have named such surfaces "superhydrophobic" to distinguish their unusual zeal to repel water. As an example in nature, water droplets will bead and roll down on some leaves.

"At the , the leaves' surfaces are 'hairy' and points of contact with water are reduced," said Chang-Jin "CJ" Kim, a UCLA professor of mechanical and aerospace engineering, and the study's principal investigator. "This reduction in points of contact means the water is held up by its own . Manmade superhydrophobic surfaces have been designed to take advantage of this phenomenon by forming microscale roughness or patterns on a hydrophobic material."

While a nonstick cooking pan is hydrophobic, it is not "oleophobic," meaning that it does not repel oil-based liquids. Cooking oil spreads out rather than beading up because it has a lower surface tension than water, making it more difficult to repel. Since the material is not oleophobic, roughening it won't make its surface oleophobic, let alone "superoleophobic."

However, in recent years scientists have created certain microscopic textures capable of making surface hydrophobic materials' surfaces not only oleophobic but also superoleophobic.

Teflon vs. superomniphobic surface. Comparing the liquid repellency of water, methanol and FC-72, a fluorinated solvent, on Teflon vs. the UCLA researchers’ new superomniphobic surface.

But a true "omniphobic" surface—one that can repel any , even those with the lowest surface tensions—has remained elusive.

Liquids with extremely low surface tension will "wet" not only the cooking pan but also even the best-performing superoleophobic surfaces today, collapsing into their microscopic texture. These liquids include fluorinated solvents, some of which are used for industrial applications like cooling electronic devices. Although the term "superomniphobic" began to be used by some, no surface was shown to repel the fluorinated solvents.

Working with Tingyi "Leo" Liu, a postdoctoral scholar in Kim's lab and the paper's lead author, Kim demonstrated for the first time true omniphobicity. The engineers formed a surface covered with thousands of microscale flathead nails, each about 20 micrometers in head diameter—each much smaller than the width of a typical human hair—resembling the appearance of existing superoleophobic textures.

Water rolling on the superomniphobic surface. Water, methanol and FC-72, a fluorinated solvent, rolling around on the UCLA researchers’ superomniphobic surface. The sides are non-engineered.

The effect had never previously been observed, either on manmade or natural surfaces. It relies solely on the physical attributes of the texture, rather than any chemical properties of the material the surface is made of. Kim said it would actually be appropriate to call it a "mechanical" surface.

The research, which was part of Liu's doctoral dissertation at UCLA, is published in the journal Science.

The key to the team's innovative design is additional nanoscale details around the nail heads. Underneath the flat head, a nanoscale thin and short "curtain" surrounds the top and droops down vertically. This overhang creates a reverse meniscus when the liquid is on the surface and suspended between the nails. These special nails, spaced about 100 micrometers apart, are reminiscent of a serif letter "T" in cross section. On this engineered surface, even completely wetting liquids roll around like a ball and slide right off when the surface tilted.

Liquids bouncing on the superomniphobic surface. Droplets of water, methanol and FC-72, a fluorinated solvent, all shown bouncing on the superomniphobic surface, slowed down 20 times.
"In a manned spaceship, you can see how a liquid will hold together as a sphere and that's because it's completely surrounded by air, that's the same idea here," Liu said. "On our textured surface, liquid sits on a cushion that is 95 percent air, and its own surface tension holds it up so it can roll over the surface without collapsing."

The surface super-repelled all available liquids, including water, oils and many solvents, qualifying to be superomniphobic. It even super-repelled a fluorinated solvent called perfluorohexane, the liquid with the lowest known surface tension.

The team made the same microscale pattern on surfaces of glass, a metal and a polymer. In each case, the engineered surface super-repelled all liquids in a series of tests.

The researchers said it could be capable of lasting a long time in an outdoor environment, such as on buildings or vehicles, because its repelling properties would not degrade from ultraviolet light exposure and extreme temperatures. And it could improve biomedical devices because its repelling properties would not degrade because of fouling by biofluids.

Kim also has a UCLA faculty appointment in bioengineering and is a member of the California NanoSystems Institute. The researchers have filed a patent on the work.

Explore further: Chemical transformation yields surface-bound microstructures that repel oil- and water-based contaminants

More information: "Turning a surface superrepellent even to completely wetting liquids," by T. Liu et al., Science, 2014. www.sciencemag.org/lookup/doi/ … 1126/science.1254787

Related Stories

Researchers create super-repellant surface material (w/ video)

January 9, 2013

(Phys.org)—Researchers from the University of Michigan working in collaboration with associates from the US Air Force have created a new type of surface cover that repels oils, water, alkali solutions, acids and even non-Newtonian ...

Smooth sailing: Rough surfaces that can reduce drag

January 17, 2014

From the sleek hulls of racing yachts to Michael Phelps' shaved legs, most objects that move through the water quickly are also smooth. But researchers from UCLA have found that bumpiness can sometimes be better.

Recommended for you

Field-responsive mechanical metamaterials (FRMMs)

December 11, 2018

In a recent study published in Science Advances, materials scientists Julie A. Jackson and colleagues presented a new class of materials architecture called field-responsive mechanical metamaterials (FRMM). The FRMMs exhibit ...

Researchers develop smartphone-based ovulation test

December 11, 2018

Investigators from Brigham and Women's Hospital are developing an automated, low-cost tool to predict a woman's ovulation and aid in family planning. Capitalizing on advancements in several areas, including microfluidics, ...

CRISPR method for conditional gene regulation

December 11, 2018

A team of engineers at the University of Delaware has developed a method to use CRISPR/Cas9 technology to set off a cascade of activities in cells, a phenomenon known as conditional gene regulation. Their method, described ...

4 comments

Adjust slider to filter visible comments by rank

Display comments: newest first

antialias_physorg
5 / 5 (1) Nov 28, 2014
And it could improve biomedical devices because its repelling properties would not degrade because of fouling by biofluids.

That would be great. However they should test to see whether biofilms can spread on this. Bacteria can extrude hairs which might be able to reach into the cracks ans hold on.

Also the pressure required to wet the surface needs to be investigated (if it's high enough then having such coatings on water pipes would make them virtually age-proof).
Selena
Nov 28, 2014
This comment has been removed by a moderator.
Nerfherder
not rated yet Nov 28, 2014
I wonder how it would behave lining a micro-fluidic chamber?
sirchick
5 / 5 (2) Nov 30, 2014
Would ships be more efficient (less water friction) with hydro phobic materials coated on the hull? Curious to know how friction is affected by these materials.

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.