Technique creates metal memory and could lead to vanishing dents

March 29, 2007

Crumpled kitchen foil that lays flat for reuse. Bent bumpers that straighten overnight. Dents in car doors that disappear when heated with a hairdryer. These and other physical feats may become possible with a technique to make memory metals discovered by researchers at the University of Illinois.

Normally, when a piece of metal – such as a paperclip – is bent, the change in shape becomes permanent. But, when heat is added to bent metal films having the right microstructure, the researchers found, the films return to their original shapes. The higher the temperature, the sooner the metal films revert. "It’s as though the metal has a memory of where it came from," said Taher A. Saif, a professor of mechanical science and engineering at Illinois, and senior author of a paper that describes the findings in the March 30 issue of the journal Science.

In the study, Saif and graduate students Jagannathan Rajagopalan and Jong H. Han explored aluminum films and gold films. The aluminum films were 200 nanometers thick, 50-60 microns wide and 300-360 microns long. The gold films were 200 nanometers thick, 12-20 microns wide and 185 microns long. The average grain size in the aluminum films was 65 nanometers; in the gold films, 50 nanometers.

"We found that the type of metal doesn’t matter, said Saif, who also is a Willett Faculty Scholar and a researcher at the university’s Micro and Nanotechnology Laboratory. "What matters is the size of the grains in the metal’s crystalline microstructure, and a distribution in the size."

Grain sizes are typically one-third to one-half the thickness of a metal film. Raising the temperature by about 50 degrees Celsius causes the grains to grow larger.

If the grains are uniformly too small, the metal will be brittle and break while being bent. If the grains are uniformly too large, the metal will bend, but then stay in that position. To return to the initial shape, what’s needed is a balance between brittleness and malleability.

That balance can be achieved through a combination of small and large grains, the researchers report.

Variations in the microstructure lead to plastic deformation in the larger grains and elastic accommodations in the smaller grains, Saif said. The bigger grains bend, but push and pull on the smaller grains, which become elastically deformed like a spring.

If the metal is then left alone, the smaller grains will release this energy and force the bigger grains back to their original shapes over time. This local release of energy can be speeded up by applying heat.

Controlling the crystalline microstructure of thin films also could reduce energy loss in oscillators and resonators used in electronic circuits, Saif said. Oscillators and resonators are found in products ranging from air bag sensors and camcorders to digital projectors and global positioning systems.

"If the grains that constitute the metal films in these devices are between 50 and 100 nanometers, they can be very lossy," Saif said. "However, if we decrease the grain size, we can reduce much of the energy loss."

Source: University of Illinois at Urbana-Champaign

Explore further: Designing new metal alloys using engineered nanostructures

Related Stories

Designing new metal alloys using engineered nanostructures

November 23, 2017

Materials science is a field that Jason Trelewicz has been interested in since he was a young child, when his father—an engineer—would bring him to work. In the materials lab at his father's workplace, Trelewicz would ...

Using polymeric membranes to clean up industrial separations

November 16, 2017

There are scores of promising technologies under development that can reduce energy consumption or capture carbon in fields including biotech, computer science, nanotechnology, materials science, and more. Not all will prove ...

Scientists revisit optical constants of ultrathin gold films

October 17, 2017

Researchers at MIPT have conducted highly precise measurements of the optical constants of ultrathin gold films with thicknesses ranging from 20 to 200 billionths of a meter in the optical part of the electromagnetic spectrum. ...

A simple additive to improve film quality

September 18, 2017

Thin films for use in solar cells are more effective when simple chemicals called glycol ethers are added to the film-forming mix, a KAUST team has found.

A little tension yields enormous solar crystals

September 26, 2017

In the race to replace silicon in low-cost solar cells, semiconductors known as metal halide perovskites are favored because they can be solution-processed into thin films with excellent photovoltaic efficiency. A collaboration ...

Recommended for you

A 100-fold leap to GigaDalton DNA nanotech

December 6, 2017

DNA, present in almost every cell, is increasingly being used as a building material to construct tiny, but sophisticated structures such as autonomous 'DNA walkers' that can move along a microparticle surface, fluorescent ...

Go with the flow (or against it)

December 6, 2017

Queen's University researchers are using magnetic fields to influence a specific type of bacteria to swim against strong currents, opening up the potential of using the microscopic organisms for drug delivery in environments ...

0 comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.