Silent aircraft readies for take-off

November 6, 2006
The silent aircraft

MIT and Cambridge University researchers will unveil the conceptual design for a silent, environmentally friendly passenger plane at a press conference Monday, Nov. 6, at the Royal Aeronautical Society in London.

"Public concern about noise is a major constraint on expansion of aircraft operations. The 'silent aircraft' can help address this concern and thus aid in meeting the increasing passenger demand for air transport," said Edward M. Greitzer, the H.N. Slater Professor of Aeronautics and Astronautics at MIT.

Greitzer and Professor Ann P. Dowling of Cambridge University are the lead principal investigators on the Silent Aircraft Initiative. This collaboration of 40 researchers from MIT and Cambridge, plus many others from more than 30 companies, was launched three years ago "to develop a conceptual design for an aircraft whose noise was almost imperceptible outside the perimeter of an airfield in an urban environment."

While originally conceived to make a huge reduction in airplane noise, the team's ultimate design also has the potential to be more fuel-efficient. In a typical flight, the proposed plane, which is designed to carry 215 passengers, is predicted to achieve 124 passenger-miles per gallon, almost 25 percent more than current aircraft, according to Greitzer. (For a down-to-earth comparison, the Toyota Prius hybrid car carrying two passengers achieves 120 passenger-miles per gallon.)

The project aims to develop aircraft by 2030.

The conceptual design addresses both the engines and the structure, or airframe, of a plane. Half of the noise from a landing plane comes from the airframe.

Other key features of the design include:

-- An overall shape that integrates body and wings into a "single" flying wing. As a result, both the body and wings provide lift, allowing a slower approach and takeoff, which would reduce noise. The shape also improves fuel efficiency.

-- The elimination of the flaps, or hinged rear sections on each wing. These are a major source of airframe noise when a plane is taking off and landing.

-- Engines embedded in the aircraft with air intakes on top of the plane rather than underneath each wing. This screens much of the noise from the ground.

-- A variable-size jet nozzle that allows slower jet propulsion during takeoff and landing but efficient cruising at higher speeds.

What will it take to turn the design into a plane by 2030?

"One major technical challenge is the integration of the propulsion system with the aircraft," Greitzer said. "The propulsion system, with engines embedded in the fuselage, is different than for traditional civil aircraft, in which the engines are located in nacelles below the wing. This presents a different set of issues to the designer."

Zoltan S. Spakovszky, C. S. Draper Associate Professor in MIT's Department of Aeronautics and Astronautics, also cited the integration of the propulsion system as a key challenge. Spakovszky and James I. Hileman, a research engineer in the department, are the chief engineers, or day-to-day managers, for the project.

He explained that in today's airplanes, with engines hanging below the wings, air flows unimpeded into the engine. In the new design, however, air traveling into the air intakes on top of the plane will behave differently. This is because the air particles flowing close to the plane's body experience friction. As a result, "the particles flow at a lower velocity near the surface of the plane than in the free (air) stream," Spakovszky said. The new engine must be designed to operate in these strongly nonuniform airflows.

A second important technical challenge involves the craft's unconventional airframe, Spakovszky said. "The structural integrity of a pressure vessel allowing this single wing-like shape needs to be ensured and poses a major challenge."

Greitzer emphasized that the collaboration between MIT, Cambridge University and their industrial partners was key to the end result.

"Collaboration and teaming occurred in essentially all aspects of the project. The Silent Aircraft Initiative has been very much an enterprise in which the whole is greater than the sum of the separate parts," he said.

Spakovszky referred to the overall team effort as the best part of the project. "Technical expectations were taken for granted, but working well across the Atlantic was not a given," he said. "It was a very, very neat experience."

Source: MIT

Explore further: Electric jet startup could become 'Uber in the sky'

Related Stories

Drone hit Canadian airliner: minister

October 16, 2017

A Canadian passenger plane landed safely after it was hit by a drone in the first case of its kind in the country, a cabinet minister said Sunday.

Deterring drones from ballparks and botanical gardens

October 13, 2017

To study how an outdoor public space might shoo away unwanted drone aircraft, researchers from Duke University are teaming up with the Durham Bulls and the Sarah P. Duke Gardens to develop a set of affordable and aesthetic ...

What happens when a bird strikes a plane?

September 25, 2017

In bowling, a strike is the best shot you can make. In aviation jargon, however, a strike happens when a bird suddenly crosses the trajectory of an aeroplane. Usually, with an adverse outcome for the bird.

Recommended for you

Enhancing solar power with diatoms

October 20, 2017

Diatoms, a kind of algae that reproduces prodigiously, have been called "the jewels of the sea" for their ability to manipulate light. Now, researchers hope to harness that property to boost solar technology.

Dutch open 'world's first 3D-printed bridge'

October 17, 2017

Dutch officials toasted on Tuesday the opening of what is being called the world's first 3D-printed concrete bridge, which is primarily meant to be used by cyclists.

0 comments

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.