Microfluidic integrated circuit could help enable home diagnostic tests (w/ Video)

Apr 21, 2010

(PhysOrg.com) -- As a way to simplify lab-on-a-chip devices that could offer quicker, cheaper and more portable medical tests, University of Michigan researchers have created microfluidic integrated circuits.

Just as electronic circuits intelligently route the flow of electricity on without external controls, these microfluidic circuits regulate the flow of fluid through their devices without instructions from outside systems.

A paper on the technology is newly published online in .

This video is not supported by your browser at this time.
One circuit is serving as the clocking signal of another circuit so that the branching fluids switch in unison.

A , or lab-on-a-chip, integrates multiple laboratory functions onto one chip just centimeters in size. The devices allow researchers to experiment on tiny sample sizes, and also to simultaneously perform multiple experiments on the same material. They can be engineered to mimic the human body more closely than the does. They could lead to instant home tests for illnesses, food contaminants and toxic gases, among other advances.

“In most microfluidic devices today, there are essentially little fingers or pressure forces that open and close each individual valve to route fluid through the device during experiments. That is, there is an extra layer of control machinery that is required to manipulate the current in the fluidic circuit,” said Shu Takayama, the principal investigator on the project. Takayama is an associate professor in the U-M Department of Biomedical Engineering.

That’s similar to how electronic circuits were manipulated a century ago. Then, with the development of the integrated circuit, the “thinking” became embedded in the chip itself—a technological breakthrough that enabled personal computers, Takayama said.

“We have literally made a microfluidic integrated circuit,” said Bobak Mosadegh, a doctoral student in Takayama’s lab who is first author of the paper.

The external controls that power today’s microfluidic devices can be cumbersome. Each valve on a chip (and there could be dozens of them) requires its own electromechanical push from an off-chip actuator or pump. This has made it difficult to shrink microfluidic systems to palm- or fingertip-sized diagnostic devices.

The Takayama lab’s innovation is a step in this direction. His research group has devised a strategy to produce the fluidic counterparts of key electrical components including transistors, diodes, resistors and capacitors, and to efficiently network these components to automatically regulate fluid flow within the device.

These components are made using conventional techniques, so they are compatible with all other microfluidic components such as mixers, filters and cell culture chambers, the researchers say.

“We’ve made a versatile control system,” Mosadegh said. “We envision that this technology will become a platform for researchers and companies in the microfluidics field to develop sophisticated self-controlled microfluidic devices that automatically process biofluids such as blood and pharmaceuticals for diagnostics or other applications.

“Just as the integrated circuit brought the digital information processing power of computers to the people, we envision our microfluidic analog will be able to do the same for cellular and biochemical information.”

The paper is titled “Integrated Elastomeric Components for Autonomous Regulation of Sequential and Oscillatory Flow Switching in Microfluidic Devices.”

Explore further: Controlling core switching in Pac-man disks

Related Stories

Make your own microfluidic device with new kit from U-M

Jul 24, 2008

A type of device called a "lab-on-a-chip" could bring a new generation of instant home tests for illnesses, food contaminants and toxic gases. But today these portable, efficient tools are often stuck in the lab themselves. ...

Music is the engine of new lab-on-a-chip device (w/ Video)

Jul 22, 2009

(PhysOrg.com) -- Music, rather than electromechanical valves, can drive experimental samples through a lab-on-a-chip in a new system developed at the University of Michigan. This development could significantly simplify the ...

Print-and-Peel Method Creates Microfluidic Devices

Dec 04, 2006

Typically, researchers create microfluidic devices using the same lithographic techniques and tools used to fabricate computer chips. Lithography is expensive and slow, factors that could limit the ultimate utility of microfluidic ...

Recommended for you

Controlling core switching in Pac-man disks

Dec 24, 2014

Magnetic vortices in thin films can encode information in the perpendicular magnetization pointing up or down relative to the vortex core. These binary states could be useful for non-volatile data storage ...

Atoms queue up for quantum computer networks

Dec 24, 2014

In order to develop future quantum computer networks, it is necessary to hold a known number of atoms and read them without them disappearing. To do this, researchers from the Niels Bohr Institute have developed ...

New video supports radiation dosimetry audits

Dec 23, 2014

The National Physical Laboratory (NPL), working with the National Radiotherapy Trials Quality Assurance Group, has produced a video guide to support physicists participating in radiation dosimetry audits.

Acoustic tweezers manipulate cell-to-cell contact

Dec 22, 2014

Sound waves can precisely position groups of cells for study without the danger of changing or damaging the cells, according to a team of Penn State researchers who are using surface acoustic waves to manipulate ...

User comments : 2

Adjust slider to filter visible comments by rank

Display comments: newest first

Going
not rated yet Apr 21, 2010
Fluidic circuits are essentially analogue comtuters. They do not step through a programme of actions in a sequence controlled by a clock, like digital computers. Instead they achieve a balance of flow which mimics a real world process. I remember they were heralded in the 1960s as the next big thing but have never made a break through into practical applications.
MobReign
not rated yet Apr 21, 2010
Unless you supply a switch (buffer) between fluidic modules to control the pressure/flow. Using microelectronics you can then program the sequence of switch operations as well as perform real-time analysis on the chemical reactions or compounds.

I approve.

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.