Local nanoscale electrical measurements for graphene

Sep 09, 2013
Topography of a graphene Hall bar, superimposed with a surface potential map obtained using the FM-KPFM technique.

Research from the National Physical Laboratory (NPL), Royal Holloway, University of London, and Linköping University, Sweden, has taken an important step towards standardising important electrical parameters of graphene such as surface potential and work function. The nascent graphene industry requires these standardised measurements so that the properties of graphene are understood well enough for it to be widely used in commercial electronic devices.

Surface potential and work function can be used for defining local (down to the nanoscale) of single layer and bilayer graphene. This is important as, while current manufacturing techniques can produce sheets of 95% single layer graphene, even small amounts of bilayer graphene in a sample can change the and affect the performance of devices.

Currently, the numerical values obtained by commonly used techniques can vary significantly and are not reliable enough to make accurate comparisons. While substrate and environmental conditions can affect the results, there are also specific instrumental problems caused by the use of different measurement methods.

This new research published in Scientific Reports, the open-access journal from Nature Publishing Group, compares the accuracy and resolution of three commonly used measurement techniques: frequency-modulated Kelvin probe force microscopy (FM-KPFM); amplitude-modulated Kelvin probe force microscopy (AM-KPFM); and spectroscopy (EFS). The results show that frequency-modulated techniques such as FM-KPFM and EFS give more accurate results of the surface potential, as well as higher , than commonly used amplitude-modulated KPFM.

Olga Kazakova, who led the work at NPL, said:

"We have shown that there are significant differences in the accuracy and resolution of the most commonly used techniques for making these measurements. This means that a lab using a frequency-modulated technique will get different values than another lab using an amplitude-modulated technique, for example. This makes it difficult to have confidence in the values and define graphene characteristics."

The paper then presents a route to the standardisation of graphene measurements made in ambient conditions, rather than in vacuum, as these conditions are more representative of the environments found in general research laboratories and industry. For example, for the studied devices the obtained work function values are 4.55±0.02 eV and 4.44±0.02 eV for single layer and bilayer graphene, respectively. It should be noted that these values are not absolute and would depend on a number of intrinsic and extrinsic parameters. However, the proposed method allows for accounting of variable environmental conditions and doping variations and provides the accurate measure of the graphene surface potential, work function and carrier concentration.

The results will improve the ability of science and industry to express the characteristics of graphene quantitatively and with increased confidence. The proposed standardised technique can also be used for many other electronic materials such as semiconductors and photovoltaics, ensuring an impact not only on the graphene industry but also in the wider world of electronics.

The paper is titled "Standardization of surface potential measurements of graphene domains."

Explore further: Express tool for graphene quality control

More information: www.nature.com/srep/2013/130906/srep02597/full/srep02597.html

add to favorites email to friend print save as pdf

Related Stories

Express tool for graphene quality control

Aug 29, 2013

The National Physical Laboratory (NPL) has collaborated with Chalmers University of Technology and Linköping University in Sweden to help develop a fast and inexpensive tool for quality control of graphene ...

Topographical approaches to measuring graphene thickness

Sep 28, 2012

(Phys.org)—Graphene has long shown potential for use in electronics, but difficulties in producing the material to a high enough quality has so far prevented the commercialisation of graphene-based devices.

Seeing an atomic thickness

May 19, 2011

Scientists from NPL, in collaboration with Linkoping University, Sweden, have shown that regions of graphene of different thickness can be easily identified in ambient conditions using Electrostatic Force ...

Recommended for you

'Exotic' material is like a switch when super thin

Apr 18, 2014

(Phys.org) —Ever-shrinking electronic devices could get down to atomic dimensions with the help of transition metal oxides, a class of materials that seems to have it all: superconductivity, magnetoresistance ...

User comments : 0

More news stories

NASA's space station Robonaut finally getting legs

Robonaut, the first out-of-this-world humanoid, is finally getting its space legs. For three years, Robonaut has had to manage from the waist up. This new pair of legs means the experimental robot—now stuck ...

Ex-Apple chief plans mobile phone for India

Former Apple chief executive John Sculley, whose marketing skills helped bring the personal computer to desktops worldwide, says he plans to launch a mobile phone in India to exploit its still largely untapped ...

Filipino tests negative for Middle East virus

A Filipino nurse who tested positive for the Middle East virus has been found free of infection in a subsequent examination after he returned home, Philippine health officials said Saturday.

Egypt archaeologists find ancient writer's tomb

Egypt's minister of antiquities says a team of Spanish archaeologists has discovered two tombs in the southern part of the country, one of them belonging to a writer and containing a trove of artifacts including reed pens ...