Patented technique key to new solar power technology

Feb 05, 2013 by Colin Poitras
Brian Willis, associate professor of chemical, materials, and biomolecular engineering, in his lab, with an X-ray photoelectron spectrometer. Credit: Sean Flynn/UConn Photo

(Phys.org)—A novel fabrication technique developed by UConn engineering professor Brian Willis could provide the breakthrough technology scientists have been looking for to vastly improve today's solar energy systems.

For years, scientists have studied the potential benefits of a new branch of that relies on incredibly small nanosized antenna arrays that are theoretically capable of harvesting more than 70 percent of the sun's and simultaneously converting it into usable electric power.

The technology would be a vast improvement over the silicon in widespread use today. Even the best silicon panels collect only about 20 percent of available , and separate mechanisms are needed to convert the stored energy to usable electricity for the commercial . The panels' limited efficiency and expensive development costs have been two of the biggest barriers to the widespread adoption of solar power as a practical replacement for traditional .

But while nanosized antennas have shown promise in theory, scientists have lacked the technology required to construct and test them. The fabrication process is immensely challenging. The nano-antennas – known as "rectennas" because of their ability to both absorb and rectify from alternating current to direct current – must be capable of operating at the speed of visible light and be built in such a way that their core pair of electrodes is a mere 1 or 2 nanometers apart, a distance of approximately one millionth of a millimeter, or 30,000 times smaller than the diameter of human hair.

The potential breakthrough lies in a novel fabrication process called selective area atomic layer deposition (ALD) that was developed by Willis, an associate professor of chemical, materials, and biomolecular engineering and the previous director of UConn's Chemical Engineering Program. Willis joined UConn in 2008 as part of an eminent faculty hiring initiative that brought an elite team of leaders in sustainable energy technology to the University. Willis developed the ALD process while teaching at the University of Delaware, and patented the technique in 2011.

It is through atomic layer deposition that scientists can finally fabricate a working rectenna device. In a rectenna device, one of the two interior electrodes must have a sharp tip, similar to the point of a triangle. The secret is getting the tip of that electrode within one or two nanometers of the opposite electrode, something similar to holding the point of a needle to the plane of a wall. Before the advent of ALD, existing lithographic fabrication techniques had been unable to create such a small space within a working electrical diode. Using sophisticated electronic equipment such as electron guns, the closest scientists could get was about 10 times the required separation. Through atomic layer deposition, Willis has shown he is able to precisely coat the tip of the rectenna with layers of individual copper atoms until a gap of about 1.5 is achieved. The process is self-limiting and stops at 1.5 nanometer separation.

The size of the gap is critical because it creates an ultra-fast tunnel junction between the rectenna's two electrodes, allowing a maximum transfer of electricity. The nanosized gap gives energized electrons on the rectenna just enough time to tunnel to the opposite electrode before their electrical current reverses and they try to go back. The triangular tip of the rectenna makes it hard for the electrons to reverse direction, thus capturing the energy and rectifying it to a unidirectional current.

Impressively, the rectennas, because of their incredibly small and fast tunnel diodes, are capable of converting solar radiation in the infrared region through the extremely fast and short wavelengths of visible light – something that has never been accomplished before. Silicon solar panels, by comparison, have a single band gap which, loosely speaking, allows the panel to convert electromagnetic radiation efficiently at only one small portion of the solar spectrum. The rectenna devices don't rely on a band gap and may be tuned to harvest light over the whole solar spectrum, creating maximum efficiency.

Illustration of a working nanosized optical rectifying antenna or rectenna. Credit: Brian Willis

The federal government has taken notice of Willis's work. Willis and a team of scientists from Penn State Altoona along with SciTech Associates Holdings Inc., a private research and development company based in State College, Pa., recently received a $650,000, three-year grant from the National Science Foundation to fabricate rectennas and search for ways to maximize their performance.

"This new technology could get us over the hump and make solar energy cost-competitive with fossil fuels," says Willis. "This is brand new technology, a whole new train of thought."

The Penn State Altoona research team – which has been exploring the theoretical side of rectennas for more than a decade – is led by physics professor Darin Zimmerman, with fellow physics professors Gary Weisel and Brock Weiss serving as co-investigators. The collaboration also includes Penn State emeritus physics professors Paul Cutler and Nicholas Miskovsky, who are principal members of Scitech Associates.

"The solar power conversion device under development by this collaboration of two universities and an industry subcontractor has the potential to revolutionize green solar power technology by increasing efficiencies, reducing costs, and providing new economic opportunities," Zimmerman says.

"Until the advent of selective atomic layer deposition (ALD), it has not been possible to fabricate practical and reproducible rectenna arrays that can harness solar energy from the infrared through the visible," says Zimmerman. "ALD is a vitally important processing step, making the creation of these devices possible. Ultimately, the fabrication, characterization, and modeling of the proposed rectenna arrays will lead to increased understanding of the physical processes underlying these devices, with the promise of greatly increasing the efficiency of conversion technology."

The process is favored by science and industry because it is simple, easily reproducible, and scalable for mass production. Willis says the chemical process is already used by companies such as Intel for microelectronics, and is particularly applicable for precise, homogenous coatings for nanostructures, nanowires, nanotubes, and for use in the next generation of high-performing semi-conductors and transistors.

Willis says the method being used to fabricate rectennas also can be applied to other areas, including enhancing current photovoltaics (the conversion of photo energy to electrical energy), thermoelectrics, infrared sensing and imaging, and chemical sensors.

A 2011 seed grant from UConn's Center for Clean Energy Engineering allowed Willis to fabricate a prototype rectenna and gather preliminary data using ALD that was instrumental in securing the NSF grant, Willis says.

Over the next year, Willis and his collaborators in Pennsylvania plan to build prototype rectennas and begin testing their efficiency. Willis compares the process to tuning in a station on a radio.

"We've already made a first version of the device," says Willis. "Now we're looking for ways to modify the rectenna so it tunes into frequencies better. I compare it to the days when televisions relied on rabbit ear antennas for reception. Everything was a static blur until you moved the antenna around and saw the ghost of an image. Then you kept moving it around until the image was clearer. That's what we're looking for, that ghost of an image. Once we have that, we can work on making it more robust and repeatable."

Willis says finding that magic point where a rectenna picks up maximum solar energy and rectifies it into electrical power will be the champagne-popping, "ah-ha" moment of the project.

"To capture the visible light frequencies, the rectenna have to get smaller than anything we've ever made before, so we're really pushing the limits of what we can do," says Willis. "And the tunnel junctions have to operate at the speed of visible light, so we're pushing down to these really high speeds to the point where the question becomes 'Can these devices really function at this level?' Theoretically we know it is possible, but we won't know for sure until we make and test this device."

Explore further: Research proves nanobubbles are superstable

Related Stories

New energy technologies promise brighter future

Nov 19, 2012

In three studies published in the current issue of Technology and Innovation – Proceedings of the National Academy of Inventors, innovators unveil creative technologies that could change our sources of energy, change our use of energy ...

Willis Tower goes solar

Mar 22, 2011

(PhysOrg.com) -- Do you know the Sears Tower? No, no you don't because for some time now it has been going by the much less famous name of the Willis Tower. While that bit of information may not be news to ...

Plasmonic device converts light into electricity

Nov 09, 2011

(PhysOrg.com) -- While the most common device for converting light into electricity may be photovoltaic (PV) solar cells, a variety of other devices can perform the same light-to-electricity conversion, such ...

Wireless power for the price of a penny

Aug 09, 2012

(Phys.org) -- The newspaper-style printing of electronic equipment has led to a cost-effective device that could change the way we interact with everyday objects.

Recommended for you

Research proves nanobubbles are superstable

18 hours ago

The intense research interest in surface nanobubbles arises from their potential applications in microfluidics and the scientific challenge for controlling their fundamental physical properties. One of the ...

User comments : 18

Adjust slider to filter visible comments by rank

Display comments: newest first

grondilu
4.8 / 5 (5) Feb 05, 2013
70% of the sun's power into usable electricity? " Simple, easily reproducible, and scalable for mass production " ? Seems too good to be true. I suspect there is catch.
Sonhouse
3 / 5 (2) Feb 05, 2013
Time will tell. This is a totally new technology, the question in my mind is how fast would this process be on the production floor?

If it takes 10 hours per square foot or something it would be a non-starter.
antialias_physorg
3.8 / 5 (5) Feb 05, 2013
I suspect there is catch.

The catch is usually in the myriad factors that make a good PV cell.
- durability
- cost of production (roll-to-roll is a lot faster, and hence cheaper, than ALD)
- availabiity of raw materials
- ability of the particular cell to make use of ambient light
- need for cooling yes/no
- ...

That's why currently we don't have a one-size-fits-all type of solar cell.

If it takes 10 hours per square foot or something it would be a non-starter.

For some applications it would still be useful (e.g. high-end solar cells for sattelites). But I agree: it probably wouldn't get as widespread use as the current cells.


Sonhouse
5 / 5 (3) Feb 05, 2013
I suspect they are going to have to engineer another technique for real production. That said, engineers have the sneaky ability to do just that:)
Sonhouse
not rated yet Feb 05, 2013
Here is a link to a company we use a lot for our sputtering systems: Kurt Lesker Co. They actually make ALD equipment already for production use:

http://www.lesker...;level=2
rah
2.7 / 5 (3) Feb 05, 2013
Unless the licensing fees are super low (or better yet, free) this won't help.
baudrunner
2.5 / 5 (2) Feb 05, 2013
Not mentioned are possible cloaking applications, with the cloaking material actually delivering energy to chargeable batteries as a bonus.

The research team should consider developing a "full" spectrum material, since if every rectenna were to be of the same dimensions then only one dominant wavelength would be captured and utilized. That would not provide complete cloaking.

All that being said, the current achievement is a great one, indeed. Brian Willis and his team deserve recognition, considering that current commercial solar cells deliver about 11% efficiency at best.
Modernmystic
3.2 / 5 (5) Feb 05, 2013
"This new technology could get us over the hump and make solar energy cost-competitive with fossil fuels," says Willis. "This is brand new technology, a whole new train of thought."


Quit promising it...just show me...
praos
1.5 / 5 (6) Feb 05, 2013
Why not try to synthesize a molecule with fiiting geometry, then polymerise it?
jibbles
not rated yet Feb 07, 2013
- need for cooling yes/no

--antialias physorg

may be alleviated in combination with v3 solar's idea?
http://phys.org/n...lat.html
bearly
1 / 5 (5) Feb 09, 2013
"The federal government has taken notice of Willis's work."
We the People will never see this technology as the "government" will steal it as soon as it is properly developed.
JRi
not rated yet Feb 09, 2013
I would have wanted to see some early figures about the eficiency of their device. If 70% is the maximum, something like 5% would be a good starting point.
Subach
4.3 / 5 (4) Feb 09, 2013
Editors: Please stop posting articles without a link the paper! I'm really tired of having to track down every other paper you post an article on. The whole point of this site is to direct me to interesting papers...
VendicarE
2 / 5 (4) Feb 09, 2013
Yes. And they will put it in a large wearhouse right beside the Arc of the Covenant that Indiana Jones found.

"We the People will never see this technology as the "government" will steal it as soon as it is properly developed." - bearlyTard

Is there some central breeding facility in the U.S. where all of you fools originate? Or are you guys free range fools?
VendicarE
1.3 / 5 (3) Feb 09, 2013
Yes. Absolutely. We'll get right on it. With your expert direction and incite, it now appears so obvious to us.

"Why not try to synthesize a molecule with fiiting geometry, then polymerise it?" - praos

Why don't you just find a chemical that allows you to grow wings and bottle it?
Urgelt
5 / 5 (2) Feb 11, 2013
I find it disturbing that public money has paid for this research, only to have the researcher lock away the resulting solution sets under patents to keep them out of the hands of the general public.
Job001
1 / 5 (1) Feb 11, 2013
I find it disturbing that public money has paid for this research, only to have the researcher lock away the resulting solution sets under patents to keep them out of the hands of the general public.

To maximize profit the inventor has to maximize volume times license revenue, not "lock away" i.e. zero volume the process. It's still a tough project to get the size down an order of magnitude below Intel finFET 22nm sizes, but a 3D approach may help results.
psommerfeld
not rated yet Feb 13, 2013
Converting the infrared! Now THAT is an important step ... given that heat is unconverted in conventional panels, and in fact de-rates output. Very important point given that global warming is here to stay.

More news stories

Research proves nanobubbles are superstable

The intense research interest in surface nanobubbles arises from their potential applications in microfluidics and the scientific challenge for controlling their fundamental physical properties. One of the ...

Google+ boss leaving the company

The executive credited with bringing the Google+ social network to life is leaving the Internet colossus after playing a key role there for nearly eight years.