Method for making nanowells drawn from a misunderstanding

Mar 15, 2011
Localized etching of a silicon (100) wafer upon hydrolysis of amidine-functionalized polystyrene latex colloids. The nanowell size can be precisely controlled with the size of the APSL colloids. No etch mask is needed and the region outside the nanowells is not etched at all. Scale Bar = 500 nm.

(PhysOrg.com) -- A safe, simple, and cheap method of creating perfectly etched micron and smaller size wells in a variety of substrates has been developed by researchers in Penn State’s Department of Chemical Engineering. Similar patterned surfaces are currently made using complex and expensive photolithography methods and etch processes under clean room conditions and used in the fabrication of many optical, electrical, and mechanical devices.

The nanowell discovery was made in the labs of Darrell Velegol and Seong Kim by Velegol’s graduate student, Neetu Chaturvedi, and Kim’s graduate student, Erik Hsiao. An article detailing their research, “Maskless Fabrication of Nanowells Using Chemically Reactive Colloids,” appeared in the online edition of the journal in January 2011. In collaboration with Chaturvedi, Hsiao was working on a project to adhere polystyrene on a silicon wafer to create nanostructures with known dimensions. When Hsiao asked her to heat one of his samples, a miscommunication led her to heat the polystyrene and silicon wafer at low temperature in water in the autoclave normally used for biological samples rather than in the vacuum furnace. When they looked at the samples under the atomic force microscope (AFM), they noticed holes had formed beneath the polystyrene particles. Further examination under the scanning electron microscope (SEM) showed them perfectly etched, pyramidal shaped holes in the substrate below the places where the amidine-functionalized polystyrene latex colloid particles had adhered to the silicon dioxide on the surface of the silicon wafer.

“We saw three holes in the sample at the first AFM imaging and didn’t know what it meant since we expected pancake-like polymer patches on the sample,” said Hsiao. They took the sample to their advisers, who were both surprised by the etched wafer. By going over the steps the students had taken, the researchers realized that the wells were produced when the water hydrolized the amidine group in the particle, and through a series of chemical reactions, created a hydroxide ion that etched the well into the silicon wafer. The holes were uniform and their size and depth were totally dependent on the size of the original polystyrene particle, although the orientation of the silicon crystal affected the shape of the wells. In one orientation (100), the wells were perfect four-sided inverted pyramids. In the other orientation (111), the wells were perfect hexagons. The four researchers called them nanowells, because the bottom dimension of the wells was only a couple of nanometers across. They soon realized that they had discovered a new maskless method for creating structures in silicon without the elaborate steps normally required in the cleanroom.

“We’re delivering hydroxide ions directly to where we want to etch,” Velegol explained. “It’s much safer and cheaper than electron beam and X-ray lithography. It’s so safe that you could practically eat these particles without any harm.”

“We think this is a quite general discovery,” Kim added. “It’s a way to deliver chemistry locally rather than in bulk. Many metals, ceramics, and other materials can be etched with this technique.”

Another potential benefit of the discovery is the ability to create patterns on curved surfaces, something that is difficult to do with conventional photolithography. Since the particles are suspended in water, they can adhere to the surface of any shape and space themselves evenly over the surface. The researchers are just beginning to come up with intriguing ideas for how to use the simple technique.

Many breakthroughs come from accidents, Velegol remarked, because once something is known, people work on it very rapidly until they have filled in all the pieces and there is less to discover. Accidents are out of the pattern. “It’s one of those situations like Pasteur said where chance favors the prepared mind. We would never even have thought to try this kind of chemistry. But Neetu had been working with these colloids for several years, and Erik had experience with the AFM, so they were well prepared to take advantage of the accident,” Velegol concluded.

Explore further: Team reveals molecular structure of water at gold electrodes

Related Stories

Big steps in creating small chips

Nov 04, 2010

(PhysOrg.com) -- Plastic, heated in a simple microwave oven, is the technique researchers at the University of Alberta and the National Institute for Nanotechnology believe could help to re-invent the manufacture ...

Microfabrication: The light approach

Mar 04, 2011

Materials that conduct electricity but which are also transparent to light are important for electronic displays, cameras and solar cells. The industry’s standard material for these applications is indium ...

Recommended for you

Quantum effects in nanometer-scale metallic structures

Oct 22, 2014

Plasmonic devices combine the 'super speed' of optics with the 'super small' of microelectronics. These devices exhibit quantum effects and show promise as possible ultrafast circuit elements, but current ...

User comments : 1

Adjust slider to filter visible comments by rank

Display comments: newest first

JamesThomas
5 / 5 (1) Mar 16, 2011
Great story. Congratulations on screwing up. This shows one of the draw backs of too much education...it restricts creativity and the ability to look outside the box.

How to Stimulate Accidents, should be a required university class.