Microfluidic integrated circuit could help enable home diagnostic tests (w/ Video)

April 21, 2010

(PhysOrg.com) -- As a way to simplify lab-on-a-chip devices that could offer quicker, cheaper and more portable medical tests, University of Michigan researchers have created microfluidic integrated circuits.

Just as electronic circuits intelligently route the flow of electricity on without external controls, these microfluidic circuits regulate the flow of fluid through their devices without instructions from outside systems.

A paper on the technology is newly published online in .

This video is not supported by your browser at this time.
One circuit is serving as the clocking signal of another circuit so that the branching fluids switch in unison.

A , or lab-on-a-chip, integrates multiple laboratory functions onto one chip just centimeters in size. The devices allow researchers to experiment on tiny sample sizes, and also to simultaneously perform multiple experiments on the same material. They can be engineered to mimic the human body more closely than the does. They could lead to instant home tests for illnesses, food contaminants and toxic gases, among other advances.

“In most microfluidic devices today, there are essentially little fingers or pressure forces that open and close each individual valve to route fluid through the device during experiments. That is, there is an extra layer of control machinery that is required to manipulate the current in the fluidic circuit,” said Shu Takayama, the principal investigator on the project. Takayama is an associate professor in the U-M Department of Biomedical Engineering.

That’s similar to how electronic circuits were manipulated a century ago. Then, with the development of the integrated circuit, the “thinking” became embedded in the chip itself—a technological breakthrough that enabled personal computers, Takayama said.

“We have literally made a microfluidic integrated circuit,” said Bobak Mosadegh, a doctoral student in Takayama’s lab who is first author of the paper.

The external controls that power today’s microfluidic devices can be cumbersome. Each valve on a chip (and there could be dozens of them) requires its own electromechanical push from an off-chip actuator or pump. This has made it difficult to shrink microfluidic systems to palm- or fingertip-sized diagnostic devices.

The Takayama lab’s innovation is a step in this direction. His research group has devised a strategy to produce the fluidic counterparts of key electrical components including transistors, diodes, resistors and capacitors, and to efficiently network these components to automatically regulate fluid flow within the device.

These components are made using conventional techniques, so they are compatible with all other microfluidic components such as mixers, filters and cell culture chambers, the researchers say.

“We’ve made a versatile control system,” Mosadegh said. “We envision that this technology will become a platform for researchers and companies in the microfluidics field to develop sophisticated self-controlled microfluidic devices that automatically process biofluids such as blood and pharmaceuticals for diagnostics or other applications.

“Just as the integrated circuit brought the digital information processing power of computers to the people, we envision our microfluidic analog will be able to do the same for cellular and biochemical information.”

The paper is titled “Integrated Elastomeric Components for Autonomous Regulation of Sequential and Oscillatory Flow Switching in Microfluidic Devices.”

Explore further: Print-and-Peel Method Creates Microfluidic Devices

Related Stories

Print-and-Peel Method Creates Microfluidic Devices

December 4, 2006

Typically, researchers create microfluidic devices using the same lithographic techniques and tools used to fabricate computer chips. Lithography is expensive and slow, factors that could limit the ultimate utility of microfluidic ...

Make your own microfluidic device with new kit from U-M

July 24, 2008

A type of device called a "lab-on-a-chip" could bring a new generation of instant home tests for illnesses, food contaminants and toxic gases. But today these portable, efficient tools are often stuck in the lab themselves. ...

Music is the engine of new lab-on-a-chip device (w/ Video)

July 22, 2009

(PhysOrg.com) -- Music, rather than electromechanical valves, can drive experimental samples through a lab-on-a-chip in a new system developed at the University of Michigan. This development could significantly simplify the ...

Recommended for you

Fusion reactors 'economically viable' say experts

October 2, 2015

Fusion reactors could become an economically viable means of generating electricity within a few decades, and policy makers should start planning to build them as a replacement for conventional nuclear power stations, according ...

Iron-gallium alloy shows promise as a power-generation device

September 29, 2015

An alloy first made nearly two decades ago by the U. S. Navy could provide an efficient new way to produce electricity. The material, dubbed Galfenol, consists of iron doped with the metal gallium. In new experiments, researchers ...

Extending a battery's lifetime with heat

October 1, 2015

Don't go sticking your electronic devices in a toaster oven just yet, but for a longer-lasting battery, you might someday heat them up when not in use. Over time, the electrodes inside a rechargeable battery cell can grow ...

Invisibility cloak might enhance efficiency of solar cells

September 30, 2015

Success of the energy turnaround will depend decisively on the extended use of renewable energy sources. However, their efficiency partly is much smaller than that of conventional energy sources. The efficiency of commercially ...

Scientists produce status check on quantum teleportation

September 30, 2015

Mention the word 'teleportation' and for many people it conjures up "Beam me up, Scottie" images of Captain James T Kirk. But in the last two decades quantum teleportation – transferring the quantum structure of an object ...


Adjust slider to filter visible comments by rank

Display comments: newest first

not rated yet Apr 21, 2010
Fluidic circuits are essentially analogue comtuters. They do not step through a programme of actions in a sequence controlled by a clock, like digital computers. Instead they achieve a balance of flow which mimics a real world process. I remember they were heralded in the 1960s as the next big thing but have never made a break through into practical applications.
not rated yet Apr 21, 2010
Unless you supply a switch (buffer) between fluidic modules to control the pressure/flow. Using microelectronics you can then program the sequence of switch operations as well as perform real-time analysis on the chemical reactions or compounds.

I approve.

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.