Engineers develop process to recycle unused paint by blending it into common plastics

March 20, 2007

Engineers at Rutgers, The State University of New Jersey, have developed a process to recycle waste latex paint – the largest component of household hazardous waste – by blending it with common plastics. In laboratory samples, these paint-blended plastics were as good as, and in some cases, superior to the same plastics made without paint.

To advance this promising technology toward commercialization, Rutgers signed a special licensing agreement with Re-Manufacturing Technologies, Inc., a new spinoff of the National Council on Paint Disposition, Inc. That group was formed by a long-time paint dealer and businessman in 2002 to develop a viable approach for reducing the disposal costs and environmental impact of waste paint products.

“Many municipalities forbid discarding paint in the trash because it’s an environmental nuisance – it spills from cans that garbage trucks crush, defacing streets and contaminating refuse-handling equipment,” said Tom Nosker, professor of Materials Science and Engineering at Rutgers and principal investigator at a university center for advanced polymer materials. “They’ve responded by accepting unwanted paint during household hazardous waste recycling days, but then they’re left holding the bag, having to contract for proper waste management at almost $9 per gallon. An effective recycling solution could cut that cost, and possibly even become a money maker.”

Nosker noted that unwanted paint has become the largest component of household hazardous waste – some 68 million gallons annually. And this doesn’t even account for large quantities of paint that commercial painters and retailers dispose because of incorrect tints and inventory miscalculations.

As part of the Rutgers center’s ongoing work in plastic recycling, Nosker and postdoctoral research fellow Jennifer Lynch tested the feasibility of blending latex paint solids with two inexpensive and widely available plastics. One is high-density polyethylene (HDPE), commonly used to make milk and laundry detergent bottles; the other is polymethyl methacrylate (PMMA), used in Plexiglas and similar acrylics to make plastic windows and lenses. The paint solids, which remain after the paint’s water-based solvent evaporates, are essentially acrylic polymers and colorants.

The engineers found that paint blended with polyethylene exhibited similar characteristics and performance as pure polyethylene, with the advantage of consuming unwanted paint and reducing the amount of HDPE feedstock. The paint and polymethyl methacrylate blends sacrificed transparency, but made the otherwise-brittle plastic more flexible and tough while maintaining stiffness and strength. As a result, paint-blended PMMA might be able to compete with more expensive plastics that combine strength and flexibility, such as for laptop computer housings that need to withstand bumps and falls.

Nosker also noted that plastics made with recycled paints could be used to make paint containers, eliminating metal cans and essentially bringing the paint product’s life cycle full-circle. It’s also possible that unused paint and the plastic paint container that holds it could be recycled together.

The engineers plan to explore recycling oil-based paints, used far less today than latex paint but representing a greater environmental threat, and look into other petroleum-based materials that unwanted paints could effectively extend.

Source: Rutgers, the State University of New Jersey

Explore further: Where is solar power headed?

Related Stories

Where is solar power headed?

July 22, 2015

Most experts agree that to have a shot at curbing the worst impacts of climate change, we need to extricate our society from fossil fuels and ramp up our use of renewable energy.

Turning paper industry waste into chemicals

June 8, 2015

Researchers at the KU Leuven Centre for Surface Chemistry and Catalysis have found a more eco-friendly way to derive lignin - a paper industry waste product - from wood and convert it into chemical building blocks. The resulting ...

Researchers convert carbon dioxide into a valuable resource

September 17, 2014

Researchers at Aalto University have opened a pilot plant that converts CO2 and slag, the by-product of steel manufacturing, into a valuable mineral product. The product, Precipitated Calcium Carbonate (PCC), is used in e.g. ...

Sustainable algae cultivation making headway

June 11, 2014

Four years after the first optimistic calculations, the experimental cultivation of algae appears to be meeting expectations. Production costs have been more than halved, while the profit made on some crop components already ...

Recommended for you

1 comment

Adjust slider to filter visible comments by rank

Display comments: newest first

xiwen
not rated yet Nov 22, 2007
Hi everybody,

for more information about pmma and pc recycling check www.heathland.nl.

This is an informative website on the process of PMMA and PC recycling. Recommended for people with an interest in recycling or people working in the industrial sector.

Best regards,

Xi Wen

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.