Single-electron ammeter based on bidirectional counting of single-electrons

Jun 19, 2006
Fig. 1. (a) Schematic diagram of a single-electron ammeter. (b) Scanning electron micrograph of the device.

Nippon Telegraph and Telephone Corporation, in collaboration with the Tokyo Institute of Technology, the Japan Science and Technology Agency, and the Tohoku University, has successfully demonstrated an extremely sensitive ammeter, in which the flow of one electron in either direction can be detected in real time. The single-electron ammeter can be used to measure extremely small currents that cannot be measured with any existing meter and to analyze the motion of individual electron. It will be useful for studying nanoelectronics and developing quantum information technologies.

This work was published in Science magazine, June 16 issue.

Conventional sensitive ammeter requires millions of electrons to detect as a current.

The new single-electron ammeter with single-electron sensitivity integrates two quantum dots and a point contact in a semiconductor device as shown in Fig. 1a. An electron entering or escaping from one of the quantum dots influences the current flowing through the point contact, and thus the change in the electron occupation in a quantum dot can be monitored. Two quantum dots are required in order to identify the direction from which the electron has entered or to which it has escaped. This bidirectional counting is essential for making a single-electron ammeter.

Single-electron ammeter based on bidirectional counting of single-electrons
Fig. 2. Counting single-electron flows through the two quantum dots.

NTT researchers fabricated the single-electron ammeter using semiconductor nanofabrication techniques (See the scanning electron micrograph in Fig. 1b). Each quantum dot (L and R) has a diameter of about 100 nanometers and is placed about 200 nanometers from the point contact.

When an electron travels through the two quantum dots, the current through the point contact shows three different values depending on the location of the electron as shown in Fig. 2. Jumping between these values can be understood as, for example, an electron entering the left dot (1), moving to the right dot (2), and escaping to the right lead (3). In this way, a single-electron flow can be detected precisely and average current can be obtained by counting the net electron flow.

In order to demonstrate the performance of the single-electron ammeter, scientists connected a single-electron transistor, which is a typical nanoelectronics device, to the ammeter as shown in the inset to Fig. 3. The obtained current flowing through the single-electron transistor shows some current peaks as in Fig. 3, which is a typical characteristics of the single-electron transistor. The measured current in the range of a few to tens of attoampares (atto means 10-18; one-billionth of a billionth), which cannot be measured with any existing current meter. The current noise, 3 attoampares peak-to-peak, is more than three orders of magnitude smaller than that in a conventional current meter.

Moreover, the correct path of an electron in the device can be traced, for instance, three forward steps followed by two backward steps. This fluctuation, current noise, arises from the particle behavior of an electron (quanta) and depends on the interaction between electrons. The single-electron ammeter would be useful for investigating quantum electron transport.

Single-electron ammeter based on bidirectional counting of single-electrons
Fig. 3. Test measurement for a single-electron transistor with the single-electron ammeter.

Photon counters, in which individual photons can be counted, have been widely used to detect faint light. Similarly, the present single-electron counter should be useful for detecting extremely small current in various applications. It should be especially useful for studies on nanoelectronics, which seek to examine electron transport through nanostructures, single molecules, and biological cells, and often require measurement of extremely small currents.

Combining the ammeter with a device that converts photons or electron-spins to electronic charges could lead to the development of sensitive detectors for light or magnetic fields. Furthermore, statistical analyses of current noise measured with the single-electron ammeter would identify quantum entanglement, in which quantum information is shared between two separated electrons.

Source: Nippon Telegraph and Telephone Corporation

Explore further: Researchers develop ultrahigh-resolution 3D microscopy technique for electric fields

Related Stories

Research shows 'mulch fungus' causes turfgrass disease

1 hour ago

Inadvertently continuing a line of study they conducted about 15 years ago, a team of Penn State researchers recently discovered the causal agent for an emerging turfgrass disease affecting golf courses around ...

Study on pesticides in lab rat feed causes a stir

3 hours ago

French scientists published evidence Thursday of pesticide contamination of lab rat feed which they said discredited historic toxicity studies, though commentators questioned the analysis.

Experiments open window on landscape formation

3 hours ago

University of Oregon geologists have seen ridges and valleys form in real time and—even though the work was a fast-forwarded operation done in a laboratory setting—they now have an idea of how climate ...

To conduct, or to insulate? That is the question

3 hours ago

A new study has discovered mysterious behaviour of a material that acts like an insulator in certain measurements, but simultaneously acts like a conductor in others. In an insulator, electrons are largely stuck in one place, ...

Recommended for you

Could black phosphorus be the next silicon?

17 hours ago

As scientists continue to hunt for a material that will make it possible to pack more transistors on a chip, new research from McGill University and Université de Montréal adds to evidence that black phosphorus ...

Better memory with faster lasers

Jul 02, 2015

DVDs and Blu-ray disks contain so-called phase-change materials that morph from one atomic state to another after being struck with pulses of laser light, with data "recorded" in those two atomic states. ...

User comments : 0

Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.