Why nanolayers buckle when microbeams bend

December 15, 2005
An x-ray beam just 100 nanometres in width functions as a

High-strength, ultra-light and elastic carbon materials are commonly used in high-performance sports goods and modern aerospace technology - for example in tennis rackets, racing tyres, heat shields and even guitars. Carbon fibres are only a few micrometres thick and mainly used to mechanically reinforce other materials, like polymers, metals, and ceramics. In tension, these kinds of fibres are stronger than most other known materials. However, compression applied parallel to the fibre axis can cause the buckling of nanoscale carbon layers - comparable to the buckling of a long, thin rod under compressive load.

An x-ray beam just 100 nanometres in width functions as a "nano-magnifier" to explore, in detail, defects and changes in carbon fibres. Image: Max Planck Institute of Colloids and Interfaces

In a novel physical experiment at the European Synchrotron Radiation Facility in Grenoble, researchers from Potsdam, Germany and Vienna have threaded both ends of micrometre thick carbon fibres through thin hollow needles in order to form fibre loops. The fibres are stretched on the outside of the loop and compressed on the inside. In-between there is a neutral zone, as we might find in a bent beam. By tugging on the ends of the fibres, the scientists were able to adjust the loop's radius, and thus also the mechanical load in the tensile and the compression region.

Oskar Paris from the Max Planck Institute of Colloids and Interfaces explains that "what is unique about the experiment is that we can make observations at many length-scales and thus gather evidence about the secret of "nano-buckling". Using a 100-nanometre wide x-ray beam, we can scan the differently distorted regions along the cross-section of the fibre. Our nano-magnifier - the diffraction of the x-ray beam -allows us to measure the local strains of the only some nanometres thick carbon layers, as well as their orientation with respect to the fibre axis."

High-tech carbon fibres are made of graphite-like carbon sheets with strong covalent atomic bonding within the sheets, and weak Van der Waals bonding between them. Almost all the physical properties - and particularly mechanical behaviour - of these materials depend on their orientation. Their tensile stiffness is as much as five times higher than that of steel, and their specific tensile strength can overcome that of steel by a factor of ten. Under compression, however, the fibres can fail. Here, the mechanical behaviour is determined by mechanical instability - carbon layers buckling at the nanoscale - in addition to the shearing of single carbon layers.

In spite of this, some carbon fibres exhibit astoundingly good shear properties. In these cases, "nano-buckling" is rarely observed - which suggests the existence of a substantial number of strong cross-links between the carbon layers. Herwig Peterlik from the University of Vienna explains that "if we could reinforce the usually very weak connections between the carbon layers in a controlled way using this kind of covalent cross-links, then in addition to carbon fibres, the highly-vaunted new carbon nanotubes would be almost ready to make the strongest ropes in the world."

This has been possible very recently with electron irradiation, which requires however a high expenditure of money and energy. The high price is also the major reason why carbon fibres, which are relatively cheap to produce, are not easily replaced by modern nanotubes. The question why these valuable cross-links occur only in some carbon fibres, while others buckle, still remains unclear.

Source: Max-Planck-Gesellschaft

Explore further: Water pathways make fuel cells more efficient

Related Stories

Water pathways make fuel cells more efficient

September 24, 2015

Researchers from the Paul Scherrer Institute (PSI) have developed a coating technique in the laboratory that could raise the efficiency of fuel cells. The PSI scientists have already applied to patent the technique, which ...

New feather findings get scientists in a flap

October 22, 2014

Scientists from the University of Southampton have revealed that feather shafts are made of a multi-layered fibrous composite material, much like carbon fibre, which allows the feather to bend and twist to cope with the stresses ...

Recommended for you

Horn of Africa drying ever faster as climate warms

October 9, 2015

The Horn of Africa has become increasingly arid in sync with the global and regional warming of the last century and at a rate unprecedented in the last 2,000 years, according to new research led by a University of Arizona ...

Scientists paint quantum electronics with beams of light

October 9, 2015

A team of scientists from the University of Chicago and the Pennsylvania State University have accidentally discovered a new way of using light to draw and erase quantum-mechanical circuits in a unique class of materials ...

A mission to a metal world—The Psyche mission

October 9, 2015

In their drive to set exploration goals for the future, NASA's Discovery Program put out the call for proposals for their thirteenth Discovery mission in February 2014. After reviewing the 27 initial proposals, a panel of ...

What are white holes?

October 9, 2015

Black holes are created when stars die catastrophically in a supernova. So what in the universe is a white hole?


Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.