Atoms Precision Placement Helps Building Nanoscale Devices

September 10, 2004
Colorized version of an image created by the NIST custom-built scanning tunneling microscope

In an effort to put more science into the largely trial and error building of nanostructures, physicists at the Commerce Department's National Institute of Standards and Technology (NIST) have demonstrated new methods for placing what are typically unruly individual atoms at precise locations on a crystal surface. Reported in the Sept. 9, 2004, online version of the journal Science, the advance enables scientists to observe and control, for the first time, the movement of a single atom back and forth between neighboring locations on a crystal and should make it easier to efficiently build nanoscale devices "from the bottom up," atom by atom.

The NIST team was surprised to find that the atoms emitted a characteristic electronic "noise" as they moved between two different types of bonding sites on the crystal surface. By converting this electronic signal into an audio signal, the researchers were able to "hear" the switching take place. The sound resembles a hip hop musician’s rhythmic "scratching" and can be used by researchers to know in real time that atoms have moved into desired positions.

Several research groups already are using specialized microscopes to build simple structures by moving atoms one at a time. The NIST advance makes it easier to reliably position atoms in very specific locations. "What we did to the atom is something like lubricating a ball bearing so that less force is required to move it," says Joseph Stroscio, co-author of the Science paper.

Such basic nanoscale construction tools will be essential for computer-controlled assembly of more complex atomic-scale structures and devices. These devices will operate using quantum physics principles that only occur at the atomic scale, or may be the ultimate miniaturization of a conventional device, such as an “atomic switch” where the motion of a single atom can turn electrical signals on and off.

The research involved using a custom-built, cryogenic scanning tunneling microscope (STM) to move a cobalt atom around on a bed of copper atoms that are closely packed in a lattice pattern. In a typical STM, a needle-like tip is scanned over an electrically conducting surface and changes in current between the tip and the surface are used to make three-dimensional images of the surface topography. The tip can be brought closer to the surface to push or pull the cobalt atom.

In the research described in Science, NIST scientists discovered that the cobalt atom responds to both the STM tip and the copper surface, and that the atom “hops” back and forth between nearby bonding sites instead of gliding smoothly. With slight increases in the current flowing through the tip to the atom, the researchers were able to make the cobalt atom heat up and vibrate and weaken the cobalt-copper bonds. This induced the cobalt atom to hop between the two types of lattice sites, with the rate of transfer controlled by the amount of current flowing.

The NIST researchers also found that they could use the STM tip to reshape the energy environment around the cobalt atom. This allows control over the amount of time the cobalt atom spends in one of the lattice sites. Using this technique the researchers found they can even trap the cobalt atom in a lattice site that the atom normally avoids. Sounds of the “protesting” atom give rise to the “hip hop” scratching sound described in Science.

A 40-nanometer-wide NIST logo

“The impact of the work is twofold,” says Stroscio. “We learned about the basic physics involved in atom manipulation, which will help us build future atomic-scale nanostructures and devices. We also learned that we can control the switching of a single atom, which has potential for controlling electrical activity in those devices.”

The experiments represent initial steps in exploring a new system of measurement, atom-based metrology, in which single atoms are used as nanoscale probes to collect information about their environment. In particular, the NIST-built instrument can be used to draw detailed maps of binding sites on a metal surface that cannot be made with standard STM measurements.

Source: NIST

Explore further: ORNL microscopy captures real-time view of evolving fuel cell catalysts

Related Stories

New design points a path to the 'ultimate' battery

October 29, 2015

Scientists have developed a working laboratory demonstrator of a lithium-oxygen battery which has very high energy density, is more than 90% efficient, and, to date, can be recharged more than 2000 times, showing how several ...

Cobalt atoms on graphene a powerful combo

October 21, 2015

Graphene doped with nitrogen and augmented with cobalt atoms has proven to be an effective, durable catalyst for the production of hydrogen from water, according to scientists at Rice University.

Recommended for you

'Material universe' yields surprising new particle

November 25, 2015

An international team of researchers has predicted the existence of a new type of particle called the type-II Weyl fermion in metallic materials. When subjected to a magnetic field, the materials containing the particle act ...

CERN collides heavy nuclei at new record high energy

November 25, 2015

The world's most powerful accelerator, the 27 km long Large Hadron Collider (LHC) operating at CERN in Geneva established collisions between lead nuclei, this morning, at the highest energies ever. The LHC has been colliding ...

Study suggests fish can experience 'emotional fever'

November 25, 2015

(—A small team of researchers from the U.K. and Spain has found via lab study that at least one type of fish is capable of experiencing 'emotional fever,' which suggests it may qualify as a sentient being. In their ...


Please sign in to add a comment. Registration is free, and takes less than a minute. Read more

Click here to reset your password.
Sign in to get notified via email when new comments are made.